Assembly; Operation - EINHELL TKS 1700 Anleitung

Anleitung_TKS_1700_4340667:_
Push the recess in the splitter into the
splitter holder (a).
Adjust the splitter as shown in Fig. 22 and
fasten using the screws (27).
8.4 Assembling/disassembling the saw
blade guard (Fig.18-19)
Set the saw blade guard (2) with screw (24)
from above onto the splitter (4), so that the
screw sits firmly in the oval hole (25).
Do not tighten the screw (24) too much; the
saw blade must be able to move freely.
Attach the extractor hose (3) to the extractor
adapter (16) and to the extraction port of the
saw blade guard (2) and screw them to the
extractor adapter with the safety clamp (16).
Connect a suitable chip extraction system to
the extractor adapter (16).
To dismantle, proceed in reverse order.
Caution:
Before starting to saw, the saw blade
guard (2) must be lowered onto to the
workpiece.
8.5 Replacing the table insert (Fig. 20-21)
If the table insert is worn or damaged, it
should be replaced, otherwise risk of injury
is increased.
Take off the saw blade guard (2) (see 8.4)
Remove the 2 countersunk screws (26)
Remove the worn table inserts (6)
Assembly of the new table inserts is to be
carried out in reverse order.
8.6 Adjusting the splitter (Fig. 17; 22)
Caution: Pull out the power plug.
Set the saw blade (5) to max. cutting depth.
Adjust and lock the cutting depth into the 0°
position (see Fig. 9.2).
Disassemble the saw blade guard (see 8.4)
Remove the table inserts (6) (see 8.5)
Loosen the fixing screws (27).
8.6.1 Setting for maximum cuts
Push up the splitter (4) until the gap
between the saw table (1) and the upper
edge of the splitter (4) is at 10cm.
The distance between saw blade (5) and
splitter (4) should be a maximum of 5mm.
(Fig. 22)
14.05.2009 9:21 Uhr Seite 21
Re-tighten the screws (27) and assemble
the table inserts (6) (see 8.4).
8.7 Assembly/Changing the saw blade
(Fig. 23)
Caution: Pull out the power plug first.
Detach the saw blade guard (2)
(see Fig. 8.4).
Remove the table inserts by loosening the 2
countersunk screws (see 8.5)
Loosen the nut (Caution! Turn the nut in
the direction in which the saw blade rotates)
by using a wrench (SW 24) on the nut and
another open-ended wrench (SW 22) on the
motor shaft to apply counter-pressure.
Remove the outer flange and withdraw the
old saw blade diagonally from the inner
flange.
Clean the blade flange thoroughly before
fitting the new blade.
Mount and fasten the new saw blade in
reverse order.
Caution: Note the running direction. The
cutting angle of the teeth must point in
running direction, i.e. forwards (see the
arrow on the blade guard).
Refit and set the table insert (6) and the saw
blade guard (2) (see 8.4, 8.5)
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.

9. Operation

9.1 ON/OFF Switch (Fig. 3)
The saw can be switched on by pressing
the green button "I". Before starting to saw,
wait until the saw blade has reached its
maximum rotation speed.
In order to switch the saw off again, the red
button "0" must be pressed.
9.2 Cutting depth (Fig. 3)
By turning the hand crank (8), the saw blade
(5) can be adjusted to the desired cutting
depth.
GB/
IE/CY
21