EINHELL TKS 1700 Anleitung Seite 20

Anleitung_TKS_1700_4340667:_
GB/
IE/CY
Anticlockwise direction:
Clockwise direction:
9.3 Setting the angle (Fig.3)
Loosen the locking grip (9)
Set the desired angle on the scale by
turning the handle.
Lock the locking grip to the desired
angularity.
9.4 Parallel stop
9.4.1. Stop height (Fig. 24-28)
The stop rail (g) of the parallel stop (7) has
two different guide faces.
According to the thickness of the material to
be cut, the stop rail must be used according
to Fig. 27 for thick material (over 25mm
workpiece thickness), and according to Fig.
28 for thin material (under 25mm workpiece
thickness.
9.4.2 Turn the stop rail (Fig. 24-28)
Loosen the wing nuts (h) first in order to turn
the stop rail (g).
Loosen the cover (j) of the stop rail.
Now the stop rail can be removed from the
chain bar (i) and replaced with the correct
guide on the guide rail.
Fasten the cover (j) to the stop rail (g).
Re-attach the wing nuts (h).
9.4.3 Cutting width (Fig. 28 - 30)
The parallel stop (7) has to be used when
making longitudinal cuts in wooden
workpieces.
The parallel stop (7) should be mounted on
the right-hand side of the saw blade (5).
Set the parallel stop (7) onto the parallel
stop chain bar (12) (Fig. 28)
On the parallel stop chain bar (12) there are
2 scales (k/l) which indicate the distance
between the stop rail (g) and saw blade (5)
(Fig. 29)
Choose the correct scale, depending on
whether the parallel stop (g) is turned for
working with thick or thin material.
22
14.05.2009 9:21 Uhr
Larger cutting depth High parallel stop (thick material): Scale k
Smaller cutting depth
Low parallel stop (thin material): Scale l
9.4.4 Adjusting the stopping length
9.5 Adjusting the parallel stop (Fig. 32)
9.6 Cross stop (Fig. 33-34)
Seite 22
Adjust the parallel stop (7) to the desired
dimension on the gauge (m) and fasten with
the eccentric lever for the parallel stop (28).
(Fig. 31)
In order to avoid jamming of the workpiece,
the stop rail (g) is longitudinally adjustable.
Rule of thumb: The rear end of the stop is
connected to an imaginary line, which
begins approximately at the middle of the
saw blade, and runs towards the rear at an
angle of 45°.
Set the required cutting width.
Slacken the thumb screws (h) and push the
stop rail (g) forward until it touches the
imaginary 45° line.
Re-tighten the wing nuts (h)
Adjust the saw blade to maximum cutting
depth (see also 9.2).
Adjust the parallel stop (7) so that the stop
rail (g) touches the saw blade (5) (Setting
for thick material, see also 9.4)
If the parallel stop (7) is not lined up with the
saw blade (5), loosen the screws (n)
enough to let the parallel stop align itself
parallel to the saw blade (5) (Fig. 32)
Re-tighten the screws (n)
Insert the cross stop (13) into the groove
(29) of the saw table.
Loosen knurled screw (30)
Turn the cross stop (13) until the arrow
points to the angle required.
Re-tighten the knurled screws (30)
When cutting larger workpieces, the cross
stop (13) can be lengthened with the stop
rail (g) of the parallel stop (7) (Fig. 34)
In order to lengthen the cross stop (13) with
the stop rail (g), the stop rail (g), the chain
bar (i) and the wing nuts (h) together with
the washer from the parallel stop (7) must
be removed. Now the stop rail is to be