Before Putting The Machine Into Operation; Assembly And Operation - EINHELL KGSZ Bedienungsanleitung

Anleitung KGSZ 210-1 Las SPK 1
6. Before putting the machine into
operation
The machine has to be set up in a stable
position, i.e. it has to be bolted to a workbench, a
universal stand or the like.
All the covers and safety devices have to be
properly fitted before the machine is switched on.
It must be possible for the saw blade to run
freely.
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machine's moving parts run smoothly.
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.

7. Assembly and operation

7.1 Setting up the saw (Fig. 1/2)
Mount the lever for the tightening screw (13) on
the back of the machine.
To adjust the turntable (8), loosen the locking
screw (10) by approx. 2 turns and push the
release button (18) which frees the turntable (8).
Keep the release button (18) pressed and turn
the turntable (8) and scale pointer (11) to the
desired angular setting on the dial (12) and lock
into place with the locking screw (10).
Lightly press the machine head (4) down while at
the same time pulling the retaining pin (16) out
from the motor mounting; this causes the saw to
move down to the lower working position.
Swing the machine head (4) up until the retaining
hook latches into place.
The clamping device (19) and the workpiece
support (20) can be fastened on both the right
and left sides of the base plate (9).
When the tightening screw (13) is loosened, you
can tilt the machine head (4) to the left by up to
45°.
7.2 Crosscut 90° and turntable 0° (Fig. 3)
For cutting widths up to 105 mm it is possible to fix
the saw's drag function with the knurled screw (14) in
rear position. If the cutting width exceeds 105mm
you must ensure that the knurled screw (14) is
slackened and that the machine head (4) can be
moved.
Move the machine head (4) to its upper position.
Use the handle (2) to push back the machine
head (4) and fix it in this position if required
(dependent on the cutting width).
28.07.2004 15:17 Uhr Seite 15
Place the piece of wood to be cut against the
stop rail (7) and on the turntable (8).
Lock the material with the clamping device (19)
on the base plate (9) to prevent the material from
moving during the cutting operation.
Push down the release lever (1) for the blade
guard to release the machine head (4).
Press the release button (29) with your thumb
and push the ON/OFF switch (3) to start the
motor. Use the handle (2) to apply steady and
light downward pressure to cut all the way
through the workpiece.
After the cutting process is finished, bring the
machine head back to its upper (home) position
and release the ON/OFF button (3).
Important! The integral resetting springs will
automatically lift the machine head. Do not
simply let go of the handle (2) after cutting, but
allow the machine head to rise slowly, applying
slight counterpressure as it does so.
7.3 Precision adjustment of the stop for crosscut
90° (Fig. 4/5/7)
Lower the machine head (4) and fasten in place
with the safety pin (16).
Slacken the tightening screw (13).
Place the angular stop (a) between the blade (5)
and the turntable (8).
Slacken the locknut and adjust the adjustment
screw (21) until the angle between the blade (5)
and the turntable (8) equals 90°.
Retighten the locknut to secure this setting.
Finally, check the position of the angle indicator
(23). If necessary, release the pointer with a
crosstip screwdriver, move to the 0° position of
the angle scale (15) and retighten the holding
screw.
7.4 Crosscut 90° and turntable 0°- 45° (Fig. 6)
With the KGSZ 210/1, right and left angular cuts can
be made from 0° to 45° to the stop rail.
Using the handle (2), set the turntable (8) to the
desired angle, i.e. the scale pointer (11) on the
turntable must coincide with the desired angular
setting (12) on the stationary base plate (9).
Retighten the locking screw (10) to secure the
turntable (8) in place.
Cut as described under section 7.2.
7.5 Miter cut 0°- 45° and turntable 0° (Fig. 4/7)
The KGSZ 210/1 can be used to make miter cuts of
0° - 45° in relation to the work face.
Move the machine head (4) to its upper position.
Fasten the turntable (8) in 0° position.
Undo the tightening screw (13) and use the
handle (2) to tilt the machine head (4) to the left
until the pointer (23) coincides with the required
angle value (15).
GB
15