Publishing Notes; Explanation Of Symbols; Tools And Aids Required - Hauff-Technik HS190 Montageanleitung

KES MA90/MA110/MA150 D/WE100/125/160 SG z/d
Contents
1

Publishing Notes ...............................................14

2

Explanation of symbols ....................................14

3

Tools and aids required ....................................14

4 Description ........................................................14
5 Assembly ...........................................................16
1 Publishing Notes
Copyright © 2020 by
Hauff-Technik GmbH & Co. KG
Department: Technical Editing
Robert-Bosch-Straße 9
89568 Hermaringen, GERMANY
Tel. +49 7322 1333-0
Fax +49 7322 1333-999
E-mail offi ce@hauff-technik.de
Internet www.hauff-technik.de
Reproduction of these installation instructions – even in
extracts – in the form of reprint, photocopy, on electro-
nic data media or using any other method requires our
written consent.
All rights reserved.
Subject to technical alterations at any time and without
prior announcement.
These installation instructions form part of the product.
Printed in the Federal Republic of Germany.
2 Explanation of symbols
1
Work stages
►
Effect/result of a work step
1
Reference numerals in drawings
3 Tools and aids required
For the correct installation the following tools and aids are
required in addition to the usual standard tools:
Aids:
cable cleaner KRMTX (Hauff)
cloth
Accessories:
1 Toolset KES MA WKZ SET (Art.-Nr.: 2128030000)
consisting of:
1 Torque spanner 4 - 20 Nm, 1/4 inch
1 Extension 150 mm, 1/4 inch
1 Socket for hex driver A/F SW 13, 1/4 inch
1 Socket for hex driver A/F SW 8, 1/4 inch
1 Flexible socket wrench
SLS 6G (Art. no.: 0352010000) respectively
SLS 6GD (Art. no.: 0352010100)
1 Lubricant GM (Art. no.: 0804020000)
16
4
KES MA (see fi g.: 1).
Legend for fi g.: 1
1
2
3
4
For connecting the Hatefl ex spiral hose to the wall insert
and plastic fl ange HSI.
Sealing set interchangeable insert WE (see fi g.: 2).
Legend for fi g.: 2
1
2
3
4
Sealing set with sleeve KES MA WE including split
interchangeable insert with segment ring technology for
sealing cables with rubber compression seal at the end of
Hatefl ex spiral tube.
5
1
2
►
3
4
Legend for fi g.: 7
1
5a
Art. Nr.: 5090033077 Rev.: 02/2020-05-19
Description
Systemcover with union nut
Rubber sleeve
Clamping strap
Spiral hose Hatefl ex
Rubber sleeve
Clamping straps
Interchangeable insert
Blind plug
Assembly
Remove completely protective foil from the cable
entry present (after warming slightly) (siehe
Abb.: 3).
If necessary, clean out concrete residue from the
wrench threads on the closing cover.
Use the SLS 6G(D) flexible socket wrench
(accessories) to open the closing cover via the
wrench threads by twisting to the left (see fig.: 4).
The system cover can be installed.
Insert the pre-assembled system cover with a slight
twist into the bayonet of the wall insert and screw
in tight clockwise to limit stop (red union nut must
not be tightened at this point) (see fi g.: 5).
The holes in the key holder on the system cover
must match with the arrows on the cable entry
(see fi g.: 6).
The red union nut is then tightened clockwise by
hand or with the SLS 6G(D) fl exible head spanner
until fl ush with the wall insert (see fi g.: 7).
Red union nut lies fl ush
Preparation of variant KES MA90 D
Apply a marking at the spiral hose at a distance of
8 cm (see fi g.: 8).
EN