Hauff-Technik HS190 Montageanleitung Seite 18

KES MA90/MA110/MA150 D/WE100/125/160 SG z/d
Spread lubricant "GM" on end of media pipe (not
a corrugated pipe) and insert in rubber sleeve as
far as it will go (see Table 2 and fi g.: 14).
Then tighten clamping strap using a torque spanner
(see Table 2).
Preparation of corrugated pipe connections
9a
– insert ring clips and system sealing rings in
corrugated pipe
Insert pipe manufacturer's system sealing rings (not
included and only available through pipe
manufacturer) at the end of the corrugated pipe
into the gaps (see fi g.: 16).
Legende zu Abb. 16
1 Systemdichtringe des Rohrherstellers
2 Clipringe
Then insert the split ring clips provided (see fi g.: 17)
into the gaps of the corrugated pipe after the
system sealing rings (see fi g.: 16). Here, care must
be taken to ensure that the ring clips are positioned
underneath the tension strap (see fi g.: 19).
Legend for fi g. 17
1 Label (e. g. System Kabufl ex)
• The ring clips must be labelled identically to
the designation of the corrugated pipe manuf-
acturer (e.g. Kabufl ex).
• Other corrugated pipe manufacturers can be
used on request.
• The end of the corrugated pipe must be cut
off at right angles so that it is clean and free
of burrs.
• Care must be taken to ensure that the ring
clips are positioned directly underneath the
tensioning clamp of the rubber sleeve.
• The pipe must not be damaged or deformed
in the area of the sealing.
Preparation of corrugated pipe connection –
9b
variant DN 90/DN 125/DN 160
Mark the spiral hose at a distance of (see Table 3
"Insertion depth (marking) of spiral tube in cm")
(see fig.: 18).
Legend for fi g. 18
1 Insertion depth of spiral tube (siehe Tabelle 3)
Push the rubber sleeve over the spiral hose to limit
stop (marking) and tighten clamping strap using a
torque spanner (see Table 3) (see fig.: 18).
Insert the end of the corrugated pipe in the rubber
sleeve as far as it will go and tighten tension strap
with torque wrench (see Table 3) (see fig.: 18 and
19).
Care must be taken to ensure that the ring clips
18
10
Legend for fi g. 20
1
2
Legend for fi g. 21
1
11
11.1
11.2
11.3
11.4
11.5
11.6
11.7
Art. Nr.: 5090033077 Rev.: 02/2020-05-19
are positioned directly underneath the tensio-
ning clamp of the rubber sleeve (see fi g.: 19).
Preparation – interchangeable insert variant
WE100/WE125/WE160
Mark the spiral hose at a distance of (see table 4
"Insertion depth (marking) of spiral tube in cm")
(see fig.: 20).
Push the rubber sleeve over the spiral hose to limit
stop (marking) and tighten clamping strap using a
torque spanner (see table 4) (see fig.: 20).
Insertion depth of spiral tube (see table 4)
Interchangeable insert
Insert cable and determine cable diameter.
Order interchangeable insert WE100 or WE125 or
WE160 (accessories).
Fold the split interchangeable insert WE100 or
WE125 or WE160 over the cables and insert into
rubber sleeve as far as it will go (see fig.: 21).
Limit stop inside the rubber sleeve
Tighten clamping straps using a torque spanner
(see Table 4) (see fig.: 20 and 21).
Preparation of interchangeable insert with
segment rings variant – WE100/WE125/WE160
Mark the spiral hose at a distance of „a" (see Table
5 and fig.: 22).
The end of the spiral tube pipe must be cut off
at right angles so that it is clean and free of
burrs (see fi g.: 22).
Push the rubber sleeve over the spiral hose to limit
stop (marking) (see fi g.: 23).
Tighten clamping strap using a torque spanner
WAF13 (see Table 5) (see fi g.: 24).
Push the closing cover into the rubber sleeve as far
as it will go and tighten the clamping straps with an
WAF13 torque wrench (see table 5) (see Fig .: 25).
Only attach the closing cover if the cables are
pulled in at a later time!
Insert cable (see fi g.: 26).
Check the dimensions of the cables (see fig.: 27).
Fold open split interchangeable insert, remove blind
plug not required and fan out segment rings (see
fig.: 28 and 29).
EN