Specifications - Makita GA7050 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Shaft lock
2-1. Switch trigger
2-2. Lock lever
3-1. Indication lamp
5-1. Wheel guard
5-2. Screw
5-3. Bearing box
6-1. Wheel guard
6-2. Bearing box
6-3. Nut
6-4. Lever
7-1. Nut
7-2. Lever
8-1. Lock nut
8-2. Depressed center wheel
8-3. Inner flange
8-4. Super flange
9-1. Lock nut
9-2. Depressed center wheel

SPECIFICATIONS

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for grinding, sanding and cutting of
metal and stone materials without the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
For Model GA7050, GA9050
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
Downloaded from www.Manualslib.com
9-3. Inner flange
10-1. Lock nut wrench
10-2. Shaft lock
11-1. Lock nut
11-2. Abrasive disc
11-3. Rubber pad
12-1. Ezynut
12-2. Abrasive wheel/Multi-disc
12-3. Inner flange
12-4. Spindle
13-1. Shaft lock
14-1. Arrow
14-2. Notch
17-1. Wire cup brush
18-1. Wire wheel brush
19-1. Lock nut
19-2. Abrasive cut-off wheel/diamond
19-3. Inner flange
Model
Depressed center wheel diameter
Spindle thread
No load speed (n )/Rated speed (n)
0
Overall length
Net weight
Safety class
manuals search engine
Explanation of general view
wheel
GA7050
180 mm
M14
-1
8,500(min )
432 mm
4.5 kg
ENE048-1
impedance equal or less than 0.22 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
ENF002-1
characteristics.
For Model GA7050, GA7050R
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
ENF100-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode : surface grinding
Vibration emission (a
4
19-4. Wheel guard for abrasive cut-off
wheel/diamond wheel
20-1. Lock nut
20-2. Outer flange 78
20-3. Abrasive cut-off wheel/diamond
wheel
20-4. Inner flange 78
20-5. Wheel guard for abrasive cut-off
wheel/diamond wheel
21-1. Exhaust vent
21-2. Inhalation vent
22-1. Commutator
22-2. Insulating tip
22-3. Carbon brush
23-1. Brush holder cap
23-2. Screwdriver
GA7050R GA9050
180 mm 230 mm
M14 M14
-1 -1
8,500(min ) 6,600(min )
455 mm 432 mm
4.6 kg 4.7 kg
/II
) : 94 dB(A)
pA
) : 105 dB(A)
WA
Wear ear protection
2
) : 6.5 m/s
h,AG
GA9050R
230 mm
M14
-1
6,600(min )
455 mm
4.8 kg
ENG102-3
ENG208-5