Specifications; Safety Instructions - Makita 5621RD Betriebsanleitung

ENGLISH
1 To avoid kickback, do support
board or panel near the cut.
2 Don't support board or panel
away from the cut.
3 A typical illustration of proper
hand support and workpiece
support.
4 Push button
5 Battery cartridge
6 Charging light
7 Battery charger
8 Loosen (counterclockwise)
9 Hex wrench
10 Shaft lock

SPECIFICATIONS

Model
Blade diameter ................................................... 165 mm
Max. cutting depth
At 90° ................................................................. 54 mm
At 45° ................................................................. 38 mm
-1
No load speed (min ) ............................................. 2,600
Overall length ..................................................... 364 mm
Net weight .............................................................. 3.8 kg
Rated voltage ....................................................D.C.18 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.

SAFETY INSTRUCTIONS

WARNING! When using battery operated tools basic
safety precautions, including the following, should
be followed to reduce the risk of fire, leaking batter-
ies and personal injury: Read these instructions
before operating this product and save these instruc-
tions.
For safe operation:
1. Keep work area clean
– Cluttered areas and benches invite injuries.
2. Consider the work environment.
– Do not expose the tool to rain. Keep work area well
lit. Do not use tools in the presence of flammable
liquids or gases.
3. Keep children away
– Do not let visitors touch the tool. Keep visitors
away from work area.
4. Store batteries or idle tools
– When not in use, tools and batteries should be
stored separately in a dry, high or locked up place,
out of reach of children.
– Ensure that battery terminals cannot be shorted
by other metal parts such as screws, nails, etc.
5. Do not force the tool
– It will do the job better and safer at the rate for
which it was intended.
6. Use the right tool
– Do not force small tools or attachments to do the
job of a heavy duty tools. Do not use tools for pur-
poses not intended.
Explanation of general view
11 Bolt
12 Outer flange
13 Saw blade
14 Inner flange
15 Hex socket head bolt
16 Cutting depth
17 Lever
18 Bevel scale plate
19 Clamp screw
20 Adjusting screw
21 Base
22 Triangular rule
23 For straight cuts
24 Cutting line
7.
5621RD
8.
9.
10. Do not abuse the supply cord (if fitted)
11. Secure the work
12. Do not over-reach
13. Maintain tools with care
14. Disconnect tools
15. Remove adjusting keys and wrenches
16. Avoid unintentional starting
17. Stay alert
25 For 45° bevel cuts
26 Switch trigger
27 Lock-off button
28 Clamp screw
29 Rip fence (Guide rule)
30 Dust nozzle
31 Screws
32 Hose 28 mm in inner dia.
33 Vacuum cleaner
34 Limit mark
35 Brush holder cap
36 Screwdriver
Dress properly
– Do not wear loose clothing or jewellery, they can
be caught in moving parts. Non-skid footwear is
recommended when working outdoors. Wear pro-
tecting hair covering to contain long hair.
Use protective equipment
– Use safety glasses and if the cutting operation is
dusty, a face or dust mask.
Connect dust extraction equipment
– If devices are provided for the connection of dust
extraction and collection ensure these are con-
nected and properly used.
– Never carry the tool by the cord or yank it to dis-
connect from the socket. Keep the cord away from
heat, oil and sharp edges.
– Use clamps or a vice to hold the work. It is safer
than using your hand and it frees both hands to
operate the tool.
– Keep proper footing and balance at all times.
– Keep cutting tools sharp and clean for better and
safer performance. Follow instructions for lubrica-
tion and changing accessories. Inspect tool cords
periodically and if damaged have repaired by an
authorized service facility.
– Where the design permits, disconnect the tool
from its battery pack when not in use, before ser-
vicing and when changing accessories such as
blades, bits and cutters.
– Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
– Do not carry the tool with a finger on the switch.
– Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
7