Specifications; Circular Saw Safety Warnings - Makita 5104 Betriebsanleitung

ENGLISH
(Original instructions)
1 Lever
2 Scale
3 Depth guide
4 Clamping nut
5 Indication
6 Angle plate
7 Base
8 Top guide
9 Rip fence (Guide rule)

SPECIFICATIONS

Model
Blade diameter ..................... 260 – 270 mm
Max. cutting depth
at 0° .................................. 95/100 mm
at 45° ................................ 69/73 mm
–1
No load speed (min ) ......... 3,800
Overall length ....................... 405 mm
Net weight ........................... 8.2 kg
Safety class ..........................
• Due to our continuing program of research and
development, the specifications herein are subject to
change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

CIRCULAR SAW SAFETY WARNINGS

Cutting procedures
1. DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on auxil-
iary handle, or motor housing. If both hands are
holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The
guard cannot protect you from the blade below the
workpiece.
4
Explanation of general view
10 Switch trigger
11 Lock-off button
12 Hex wrench
13 Shaft lock
14 Hex bolt
15 Outer flange
16 Saw blade
17 Inner flange
18 Rear handle
5104 5104S
270 mm
95/100 mm
69/73 mm
3,800
405 mm
8.2 kg
/II
ENE078-2
ENF002-2
GEA010-2
GEB133-2
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold the workpiece in your hands or
across your leg while cutting. Secure the work-
piece to a stable platform. It is important to sup-
port the work properly to minimise body exposure,
blade binding, or loss of control.
/II
000157
5. Hold the power tool by insulated gripping sur-
faces, when performing an operation where the
cutting tool may contact hidden wiring or its own
cord. Contact with a "live" wire will also make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run off-centre, causing loss of control.
8. Never use damaged or incorrect blade washers
or bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Kickback causes and related warnings
– kickback is a sudden reaction to a pinched, jammed
or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the
operator;
– when the blade is pinched or jammed tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the oper-
ator;
19 Front handle
20 Vacuum cleaner
21 Adjusting screw
22 Triangular rule
23 Limit mark
24 Brush holder cap
25 Screwdriver