Specifications - Makita DHS710 Bedienungsanleitung

ENGLISH (Original instructions)
1-1. Red indicator
1-2. Button
1-3. Battery cartridge
2-1. Battery indicator
2-2. Overheat indicator
3-1. Star marking
4-1. Lever
5-1. Front lever
6-1. Rear wing nut
7-1. Stopper
8-1. Cutting line (0 ﾟ position)
8-2. Cutting line (45 ﾟ position)
8-3. Screw
9-1. Switch trigger
9-2. Lock-off lever
10-1. Hex wrench
10-2. Loosen
10-3. Tighten
10-4. Shaft lock

SPECIFICATIONS

Max. cutting depth
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
Noise
The typical
according to EN60745:
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB (A)
Downloaded from www.Manualslib.com
Explanation of general view
11-1. Mounting shaft
11-2. Inner flange
11-3. Saw blade
11-4. Outer flange
11-5. Hex bolt
12-1. Inner flange
12-2. Saw blade
12-3. Outer flange
12-4. Hex bolt
13-1. Mounting shaft
13-2. Inner flange
13-3. Saw blade
13-4. Outer flange
13-5. Hex bolt
14-1. Mounting shaft
14-2. Inner flange
14-3. Saw blade
14-4. Outer flange
14-5. Hex bolt
Model
Blade diameter
at 0°
at 45°
at 50°
-1
No load speed (min )
Overall length
Net weight
Rated voltage
A-weighted noise level
) : 85 dB (A)
pA
) : 96 dB (A)
WA
Wear ear protection
manuals search engine
ENE078-2
Vibration
The vibration
determined according to EN60745:
Work mode : cutting wood
Vibration emission (a
ENG905-1
Uncertainty (K) : 1.5 m/s
determined
The declared vibration emission value has been
•
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
•
used in a preliminary assessment of exposure.
4
14-6. Ring
15-1. Hex wrench
16-1. Dust nozzle
16-2. Screw
17-1. Vacuum cleaner
17-2. Hose
19-1. Clamping lever
19-2. Rip fence (Guide rule)
20-1. Adjusting screw for 45 ﾟ
20-2. Adjusting screw for 0 ﾟ
21-1. Triangular rule
22-1. Base
22-2. Screw
22-3. Saw blade
23-1. Limit mark
24-1. Screwdriver
24-2. Brush holder cap
DHS710
185 - 190 mm
66 - 68.5 mm
47.5 - 49 mm
42.5 - 44 mm
4,800
356 mm
4.7 kg
D.C. 36 V
total value (tri-axial vector
2
) : 2.5 m/s or less
h,W
2
ENG900-1
sum)
ENG901-1