Safety Warnings - Makita DFT023F Betriebsanleitung

WARNING:
The vibration emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
T h e E C d e c laration o f c on f ormit y is in c lu d e d as A nne x A
to t h is instru c tion manual.
SAFETY W ARNINGS
General power tool safety warnings
WARNING:
Read all safety warnings, instruc-
tions, illustrations and speci cations provided
with this power tool. F ailure to f ollo w all instru c tions
listed below may result in electric shock, fire and/or
serious in j ur y .
Save all warnings and instruc-
tions for future reference.
T h e term " po w er tool " in t h e w arnings re f ers to y our
mains-operate d ( c or d e d ) po w er tool or batter y -operate d
( c or d less ) po w er tool.
Cordless screwdriver safety warnings
Hold the power tool by insulated gripping
1 .
surfaces, when performing an operation
where the fastener may contact hidden wiring.
F asteners c onta c ting a " li v e " w ire ma y make
e x pose d metal parts o f t h e po w er tool " li v e " an d
c oul d gi v e t h e operator an ele c tri c s h o c k.
2. Al ays be sure you have a rm footing.
Be sure no one is below when using the tool in
high locations.
3. Hold the tool rmly.
Keep hands away from rotating parts.
4 .
5 . Do not touch the bit or the workpiece immedi-
ately after operation ; they may be extremely
hot and could burn your skin.
6 . Always secure workpiece in a vise or similar
hold-down device.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product (gained from repeated use) replace strict
adherence to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1 . Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery char-
ger, (2) battery, and (3) product using battery.
2. Do not disassemble battery cartridge.
If operating time has become excessively
3.
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4 . If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5 . Do not short the battery cartridge:
( 1 ) Do not touch the terminals with any con-
ductive material.
( 2 ) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
( 3 ) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
o , overheating, possible burns and even a
breakdown.
6 . Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ° C (122 ° F).
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a re.
8 . Be careful not to drop or strike battery.
9 . Do not use a damaged battery.
1 0. The contained lithium-ion batteries are subject to
the Dangerous Goods Legislation requirements.
F or c ommer c ial transports e.g. b y t h ir d parties,
f or w ar d ing agents, spe c ial re q uirement on pa c k-
aging an d labeling must be obser v e d .
F or preparation o f t h e item being s h ippe d , c onsult-
ing an e x pert f or h a z ar d ous material is re q uire d .
P lease also obser v e possibl y more d etaile d
national regulations.
T ape or mask o f f open c onta c ts an d pa c k up t h e
batter y in su c h a manner t h at it c annot mo v e
aroun d in t h e pa c kaging.
1 1 . W hen disposing the battery cartridge, remove
it from the tool and dispose of it in a safe
place. Follow your local regulations relating to
disposal of battery.
1 2. Use the batteries only with the products
speci ed by Makita. I nstalling t h e batteries to
non-compliant products may result in a fire, exces-
si v e h eat, e x plosion, or leak o f ele c trol y te.
1 3. If the tool is not used for a long period of time,
the battery must be removed from the tool.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U se o f non-genuine Makita batteries, or batteries t h at
h a v e been altere d , ma y result in t h e batter y bursting
causing fires, personal injury and damage. It will
also v oi d t h e Makita w arrant y f or t h e Makita tool an d
c h arger.
5 ENGLISH