Makita DFT023F Betriebsanleitung Seite 7

Lighting up the front lamp
Fig.4: 1. L amp
CAUTION:
Do not look in the light or see the
source of light directly.
P ull t h e s w it c h trigger to lig h t up t h e lamp. T h e lamp
keeps on lig h ting w h ile t h e s w it c h trigger is being pulle d .
T h e lamp goes out appro x imatel y 1 0 se c on d s a f ter
releasing t h e s w it c h trigger.
NOTE: U se a d r y c lot h to w ipe t h e d irt o f f t h e lens o f
t h e lamp. Be c are f ul not to s c rat c h t h e lens o f lamp, or
it ma y lo w er t h e illumination.
LED indicator / Beeper
Fig.6: 1. L E D in d i c ator
L E D in d i c ator / Beeper on t h e tool s h o w s t h e f ollo w ing f un c tions.
Function
A uto-stop w ith f astening
c ompletion
Alarm against insuffi-
c ient f astening
A larm f or low battery
c apac ity
A uto-stop w ith low
remaining battery
c apac ity
C h ec k of th e L ED ind i-
c ator, ligh t and beeper
operation
A nti-reset of c ontroller
O v erh eat protec tion
D etec tion of sw itc h
trigger operation w h en
installing battery
Motor f ailure d etec tion
Status of the tool
T h e preset f asten- L igh ts up in green f or
ing torq ue h as been approx imately one
ac h iev ed and th e tool sec ond .
h as stopped .
T h e preset f astening L igh ts up in red .
torq ue h as not been
ac h iev ed , bec ause
th e sw itc h trigger h as
released bef ore c omplet-
ing th e f astening.
T h e battery pow er F lic kers in red slow ly .
bec ame low and it is
time to replac e th e
battery c artrid ge.
T h e battery pow er is L igh ts up in red .
almost used up and th e
tool stopped .
W h en th e battery Lights up first in green,
c artrid ge is installed , nex t red .
th e tool c h ec ks f or its ( A nd th en th e ligh t
L ED ind ic ator, ligh t and c omes on.)
beeper.
T h e battery v oltage F lic kers in red and green
d ropped abnormally f or alternativ ely .
some reason, and th e
tool stopped .
T ool' s c ontroller h eated F lic kers in red q uic kly .
up abnormally and th e
tool stopped .
W h en th e battery c ar- F lic kers in red and green
trid ge is installed w ith alternativ ely .
th e sw itc h trigger pulled ,
th e tool stops to av oid
unintentional start.
Motor f ailure h as been F lic kers in red and green
d etec ted . A t th is time, alternativ ely .
tool d oes not w ork.
Reversing switch action
Fig.5: 1. R e v ersing s w it c h le v er
CAUTION:
rotation before operation.
CAUTION:
the tool comes to a complete stop. C h anging t h e
d ire c tion o f rotation be f ore t h e tool stops ma y d am-
age t h e tool.
CAUTION:
always set the reversing switch lever to the neu-
tral position.
T h is tool h as a re v ersing s w it c h to c h ange t h e d ire c tion
o f rotation. D epress t h e re v ersing s w it c h le v er f rom t h e
A si d e f or c lo c k w ise rotation or f rom t h e B si d e f or c oun-
ter c lo c k w ise rotation.
W h en t h e re v ersing s w it c h le v er is in t h e neutral posi-
tion, t h e s w it c h trigger c annot be pulle d .
Status of the LED indicator/beeper
LED indicator
A long beep
A series of long beeps
A long beep
A series of v ery sh ort
beeps
A series of sh ort beeps
A series of sh ort beeps
A series of sh ort beeps
A series of sh ort beeps
7 ENGLISH
Always check the direction of
Use the reversing switch only after
W hen not operating the tool,
Action to be taken
Beeper
–
R etigh ten th e sc rew .
R eplac e th e battery w ith
f ully c h arged one.
R eplac e th e battery w ith
f ully c h arged one.
R eplac e th e battery w ith
f ully c h arged one.
R emov e th e battery c ar-
trid ge immed iately and
c ool th e tool d ow n.
R elease th e sw itc h
trigger.
A sk y our loc al Makita
S erv ic e C enter f or repair.
–
–