Adjusting The Bevel Angle - Makita LS1219 Betriebsanleitung

First, unplug the tool. Loosen all the screws (2 each
on left and right) securing the kerf boards until the kerf
boards can still be easily moved by hand. Lower the
handle fully, then pull and turn the stopper pin to lock
the handle in the lowered position. Release the stopper
pin on the sliding pole and pull the carriage toward you
fully. Adjust the kerf boards so that the kerf boards just
contact the sides of the blade teeth. Tighten the front
screws (do not tighten firmly). Push the carriage toward
the guide fence fully and adjust the kerf boards so that
the kerf boards just contact the sides of blade teeth.
Tighten the rear screws (do not tighten firmly).
After adjusting the kerf boards, release the stopper
pin and raise the handle. Then tighten all the screws
securely.
After setting the bevel angle ensure
NOTICE:
that the kerf boards are adjusted properly. Correct
adjustment of the kerf boards will help provide proper
support of the workpiece minimizing workpiece tear
out.
Maintaining maximum cutting
capacity
This tool is factory adjusted to provide the maximum
cutting capacity for a 305 mm saw blade.
When installing a new blade, always check the lower
limit position of the blade and if necessary, adjust it as
follows:
First, unplug the tool. Turn the stopper lever to engaged
position.
► Fig.12: 1. Stopper lever
Push the carriage toward the guide fence fully and
lower the handle completely.
Adjust the blade position by turning the adjusting bolt
with the hex wrench. The periphery of the blade should
extend slightly below the top surface of the turn base
and also comes to the point where the front face of the
guide fence meets the top surface of the turn base.
► Fig.13: 1. Adjusting bolt
► Fig.14: 1. Top surface of turn base 2. Periphery of
blade 3. Guide fence
With the tool unplugged, rotate the blade by hand while
holding the handle all the way down to be sure that
the blade does not contact any part of the lower base.
Re-adjust slightly, if necessary.
After adjustment, always return the stopper lever to the
original position.
After installing a new blade and
WARNING:
with the tool unplugged, always be sure that the
blade does not contact any part of the lower base
when the handle is lowered completely. If a blade
makes contact with the base it may cause kickback
and result in serious personal injury.
Stopper arm
The lower limit position of the blade can be easily
adjusted with the stopper arm. To adjust it, turn the
stopper arm in the direction of the arrow as shown in the
figure. Turn the adjusting screw so that the blade stops
at the desired position when lowering the handle fully.
► Fig.15: 1. Stopper arm 2. Adjusting screw
Adjusting the miter angle
CAUTION:
secure the turn base by tightening the grip firmly.
NOTICE:
raise the handle fully.
► Fig.16: 1. Lock lever 2. Grip 3. Releasing lever
Rotate the grip counterclockwise to unlock the turn
base. Turn the grip while holding down the lock lever to
move the turn base. Align the pointer with your desired
angle on the scale then tighten the grip.
NOTE: If you depress the releasing lever, you can
move the turn base without holding down the lock
lever. Tighten the grip at your desired position.
This miter saw employs positive stop function. You can
set 0°, 15°, 22.5°, 31.6°, 45°, and 60° right/left miter
angle quickly. To use this function, move the turn base
close to your desired positive stop angle while holding
down the lock lever. Then release the lock lever and
move the turn base forward until the turn base is locked.

Adjusting the bevel angle

NOTICE:
and vertical vise before adjusting the bevel angle.
NOTICE:
to position the kerf boards appropriately as
explained in the "Kerf boards" section.
NOTICE:
raise the handle fully.
NOTICE:
so may cause malfunction of the locking mecha-
nism of the bevel angle.
1. Turn the knob on the slide pole counterclockwise.
► Fig.17: 1. Knob
2. Pull and turn the latch lever to the position as illustrated.
► Fig.18: 1. Latch lever
3. Match the pointer with your desired angle on the
scale by moving the carriage then tighten the knob.
► Fig.19: 1. Bevel angle scale 2. Pointer
To tilt the carriage to the right, tilt the carriage to the left
slightly and then tilt it to the right while pressing down
the releasing button.
► Fig.20: 1. Releasing button
If you perform a bevel cut greater than 45°, move the
carriage while sliding the releasing lever toward the
front of the tool. You can perform up to 48° bevel cut.
► Fig.21: 1. Releasing lever
This miter saw employs positive stop function. You can set
22.5° and 33.9° angle to both right and left quickly. Set the
latch lever in the position as illustrated and tilt the carriage. To
change the angle, pull the latch lever and tilt the carriage.
► Fig.22: 1. Latch lever
CAUTION:
always secure the knob.
20 ENGLISH
Автотовари «130»
After changing the miter angle, always
When turning the turn base, be sure to
4. Pointer
Always remove the upper guide fences
When changing bevel angles, be sure
When tilting the saw blade, be sure to
Do not tighten the knob too hard. Doing
After changing the bevel angle,