Maintenance; Adjusting The Cutting Angle - Makita LS0815F Bedienungsanleitung

15 mm Over 450 mm
1
45 mm 103 mm
103 mm
1. Holes
014279
CAUTION:
Use straight wood of even thickness as the wood
•
facing.
WARNING:
Use screws to attach the wood facing to the
•
guide fence. The screws should be installed
so that the screw heads are below the surface
of the wood facing so that they will not
interfere with the positioning of the material
being cut. Misalignment of the material being cut
can case unexpected movement during the cutting
operation which may result in a loss of control and
serious personal injury.
NOTICE:
When the wood facing is attached, do not turn the
•
turn base with the handle lowered. The blade
and/or the wood facing will be damaged.
9. Groove cutting
Fig.38
A dado type cut can be made by proceeding as
follows:
Adjust the lower limit position of the blade using
the adjusting screw and the stopper arm to limit
the cutting depth of the blade. Refer to "Stopper
arm" section described previously.
After adjusting the lower limit position of the blade,
cut parallel grooves across the width of the
workpiece using a slide (push) cut as shown in the
figure. Then remove the workpiece material
between the grooves with a chisel.
WARNING:
Do not attempt to perform this type of cut by
•
using a wider type blade or dado blade.
Attempting to make a groove cut with a wider
blade or dado blade could lead to unexpected
cutting results and kickback which may result in
serious personal injury
Be sure to return the stopper arm to the
•
original position when performing other than
groove cutting. Attempting to make cuts with the
stopper arm in the incorrect position could lead to
unexpected cutting results and kickback which
may result in serious personal injury.
CAUTION:
Be sure to return the stopper arm to the original position
•
when performing other than groove cutting.
All manuals and user guides at all-guides.com
62 mm-65 mm
18 mm
1
65 mm
Carrying tool
Fig.39
Make sure that the tool is unplugged. Secure the blade at 0°
bevel angle and the turn base at the full right miter angle
position. Secure the slide poles so that the lower slide pole is
locked in the position of the carriage fully pulled to operator
and the upper poles are locked in the position of the carriage
fully pushed forward to the guide fence (refer to the section
titled "Slide lock adjustment ".) Lower the handle fully and lock
it in the lowered position by pushing in the stopper pin.
Wind the power supply cord using the cord rests.
WARNING:
Stopper pin is only for carrying and storage
•
purposes and should never be used for any
cutting operations. The use of the stopper pin for
cutting operations
movement of the saw blade resulting in kickback
and serious personal injury.
Carry the tool by holding both sides of the tool base as
shown in the figure. If you remove the holders, dust bag,
etc., you can carry the tool more easily.
CAUTION:
Always secure all moving portions before carrying
•
the tool. If portions of the tool move or slide while
being carried loss of control or balance may occur
resulting in personal injury.

MAINTENANCE

WARNING:
Always be sure that the tool is switched off
•
and unplugged before attempting to perform
inspection or maintenance. Failure to unplug
and switch off the tool may result in accidental
start up of the tool which may result in serious
personal injury.
Always be sure that the blade is sharp and clean
•
for the best and safest performance. Attempting a
cut with a dull and /or dirty blade may cause kickback
and result in a serious personal injury.
NOTICE:
Never use gasoline, benzine, thinner, alcohol or the like.
•
Discoloration, deformation or cracks may result.

Adjusting the cutting angle

This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
1. Miter angle
Fig.40
Push the carriage toward the guide fence and tighten
the locking screw to secure the carriage.
Loosen the grip which secures the turn base. Turn the
turn base so that the pointer points to 0° on the miter
18
may cause unexpected