Makita LS1219 Betriebsanleitung Seite 29

Special Max Width Cutting
Capacities Technique
The maximum width cutting capacity of this tool can be
achieved by following the steps below:
For the maximum cutting width of this tool refer to the
SPECIFICATIONS under "Cutting capacities for special
cuttings".
1. Set the tool at 0° or 45° miter angle and make sure
that the turn base is locked. (Refer to the section titled
"Adjusting the miter angle".)
2. Remove both right and left upper fences temporar-
ily and set aside.
3. Cut a platform to the dimensions indicated in the
figure using a 38 mm thick, flat stock material such as
wood, plywood or particle board.
► Fig.55: 1. 0° Miter angle: Over 450 mm 2. 45° Miter
angle: Over 325 mm 3. 38 mm 4. Over
760 mm
Be sure to use flat stock as a
WARNING:
platform. Stock that is not flat may move during the
cutting operation which may result in kickback and
serious personal injury.
NOTE: The maximum cutting capacity in height will
be reduced by the same amount as the platform
thickness.
4. Place the platform on the tool so that it extends
equally over each side of the tool base.
Secure the platform to the tool using four 6 mm wood
screws through four holes in the lower fences.
► Fig.56: 1. Screws (two each side) 2. Lower fence
3. Base 4. Platform
Make sure that the platform is lay-
WARNING:
ing flat against the tool base and secured firmly
to the lower fences using the four screw holes
provided. Failure to properly secure the platform may
result in movement and possible kickback resulting in
serious personal injury.
Ensure that the tool is firmly
WARNING:
mounted to a stable and flat surface. Failure to
properly mount and secure the tool could cause the
tool to be unstable resulting in a loss of control and/
or the tool falling which may result in serious personal
injury.
5. Install the upper fences on the tool.
Do not use the tool without upper
WARNING:
fences installed. The upper fences provide the ade-
quate support required to cut the workpiece.
If the workpiece is not supported properly, it may
move resulting in possible loss of control, kickback
and serious personal injury.
6. Place the workpiece to be cut on the platform
secured to the tool.
Secure the workpiece firmly against the upper
7.
fences with a vise before cutting.
► Fig.57: 1. Upper fence 2. Vertical vise 3. Workpiece
4. Platform
8. Make a cut through the workpiece slowly accord-
ing to the operation titled "Slide (push) cutting (cutting
wide workpieces)."
WARNING:
secured with the vise and make the cut slowly.
Failure to do so may cause the workpiece to move
resulting in possible kickback and serious personal
injury.
WARNING:
become weakened after several cuts are per-
formed at various miter angles. If the platform
becomes weakened due to the multiple kerf cuts left
in the material, the platform should be replaced. If the
weakened platform is not replaced, it may cause the
workpiece to move, during cutting, resulting in possi-
ble kickback and serious personal injury.
Carrying tool
Before carrying, make sure to unplug and all movable
parts of the miter saw are secured. Always check the
following:
• The tool is unplugged.
• The carriage is at 0° bevel angle position and
secured.
• The carriage is lowered and locked.
• The carriage is fully slid to the guide fence and
locked.
• The turn base is at the full right miter angle posi-
tion and secured.
• The holders are stored and secured.
Carry the tool by holding both sides of the tool base as
shown in the figure.
► Fig.58
WARNING:
is for carrying and storage purposes only and not
for any cutting operations. The use of the stopper
pin for cutting operations may cause unexpected
movement of the saw blade resulting in kickback and
serious personal injury.
CAUTION:
before carrying the tool. If portions of the tool move
or slide while being carried, loss of control or balance
may occur and result in personal injury.
MAINTENANCE
WARNING:
switched off and unplugged before attempting
to perform inspection or maintenance. Failure to
unplug and switch off the tool may result in accidental
start up of the tool which may result in serious per-
sonal injury.
WARNING:
sharp and clean for the best and safest perfor-
mance. Attempting a cut with a dull and /or dirty blade
may cause kickback and result in a serious personal
injury.
28 ENGLISH
Автотовари «130»
Ensure that the workpiece is
Be aware that the platform may
Stopper pin for carriage elevation
Always secure all moving portions
Always be sure that the tool is
Always be sure that the blade is