Adjusting The Bevel Angle - Makita LS002G Betriebsanleitung

Adjusting the bevel angle

CAUTION:
After changing the bevel angle,
always secure the arm by tightening the grip dial
clockwise.
NOTICE:
Always remove the upper guide fences
and vertical vise before adjusting the bevel angle.
NOTICE:
When tilting the circular saw blade, be
sure that the carriage is fully raised.
NOTICE:
When changing bevel angles, be sure
to reposition the kerf boards appropriately as
explained in the section for positioning kerf
boards.
NOTICE:
Do not tighten the grip dial too hard.
Doing so may cause malfunction of the locking
mechanism of the bevel angle.
Tilting the circular saw blade to the
left
1. Rotate the grip dial counterclockwise.
2. Hold the handle and tilt the carriage to the left.
3.
Align the pointer with your desired angle on the
bevel angle scale.
4. Tighten the grip dial clockwise to secure the arm.
► Fig.24: 1. Grip dial 2. Handle 3. Pointer 4. Bevel
angle scale
Tilting the circular saw blade to the
right
1. Rotate the grip dial counterclockwise.
2. Hold the handle and tilt the carriage to the left
slightly.
3.
Tilt the carriage to the right while pulling the
releasing lever for right side bevel angle.
4. Align the pointer with your desired angle on the
bevel angle scale.
5. Tighten the grip dial clockwise to secure the arm.
► Fig.25: 1. Grip dial 2. Handle 3. Releasing lever for
right side bevel angle 4. Pointer 5. Bevel
angle scale
Tilting the circular saw blade beyond
the range 0° - 45°
1. Rotate the grip dial counterclockwise.
2. Hold the handle and tilt the carriage through 45°
either to the left or right.
3. Pull the carriage back slightly and turn the releas-
ing lever for 48° bevel angle in clockwise direction.
4.
Tilt the carriage further to the left or right while
keeping the lever released.
5. Tighten the grip dial clockwise to secure the arm.
► Fig.26: 1. Grip dial 2. Handle 3. Releasing lever for
48° bevel angle
Switch action
WARNING:
tridge(s) into the tool, always check to see that
the switch trigger actuates properly and returns
to the "OFF" position when released. Do not pull
the switch trigger hard without pressing in the
lock-off button. This can cause switch breakage.
Operating a tool with a switch that does not actuate
properly can lead to loss of control and serious per-
sonal injury.
WARNING:
operative switch trigger. Any tool with an inoper-
ative switch is HIGHLY DANGEROUS and must be
repaired before further usage or serious personal
injury may occur.
WARNING:
by taping down or some other means. A switch with
a negated lock-off button may result in unintentional
operation and serious personal injury.
WARNING:
you simply pull the switch trigger without press-
ing the lock-off button. A switch in need of repair
may result in unintentional operation and serious
personal injury. Return tool to a Makita service center
for proper repairs BEFORE further usage.
► Fig.27: 1. Switch trigger 2. Lock-off button 3. Hole
for padlock
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided. To start the tool,
press in the lock-off button and pull the switch trigger.
Release the switch trigger to stop.
A hole is provided in the switch trigger for insertion of a
padlock to lock the tool off.
WARNING:
or cable any smaller than 6.35 mm in diameter. A
smaller shank or cable may not properly lock the tool
in the off position and unintentional operation may
occur resulting in serious personal injury.
Casting a cutting line
CAUTION:
The lamp is not a rainproof. Do not
wash the lamp in water or use it in a rain or a wet
area. Such a conduct can cause an electric shock
and fume.
CAUTION:
Do not touch the lens of the lamp
as it is very hot while it is lighted or shortly after it
is turned off. This may cause burns.
CAUTION:
Do not apply impact to the lamp,
which may cause damage or shorted service time to it.
CAUTION:
Do not look in the light or see the
source of light directly.
The LED lamp casts a light over the circular saw blade,
and a shadow of the blade falls onto a workpiece serv-
ing as a calibration-free cutting line indicator. Press the
lamp button to shed a light. A line appears in which the
blade will meet the surface of the workpiece, becoming
deepened as the blade gets lowered.
► Fig.28: 1. Lamp button 2. Lamp 3. Cutting line
23 ENGLISH
Before installing the battery car-
NEVER use tool without a fully
NEVER defeat the lock-off button
NEVER use the tool if it runs when
Do not use a lock with a shank