Phoenix Contact MCR-FL-D-U-I-2SP-24 Bedienungsanleitung Seite 18

1 Safety instructions and warnings ................................................................................. 3
1.1 Use according to the intended purpose ........................................................ 4
2. Technical Data
2.1 Miscellaneous Data ......................................................................................................... 5
2.2 Electrical Data .................................................................................................................. 5
2.2.1 Power Supply ..................................................................................................... 5
2.2.2 Inputs ................................................................................................................... 5
2.2.3 Outputs
2.3 Mechanical Data .............................................................................................................. 7
2.4 Environmental conditions ................................................................................................ 7
2.5 Delivery .............................................................................................................................. 7
2.6 Order Code ........................................................................................................................ 7
3. Mounting ........................................................................................................................... 8
4. Electrical Connections
4.1 Measuring inputs ............................................................................................................. 8
4.2 Control Inputs and Auxiliary Power Supply ................................................................. 9
4.3 Power Supply and Alarm Outputs ................................................................................ 9
5. Parameter Setup
5.1 Parameter mode ..............................................................................................................10
5.2 Parameter input for Instantaneous Value ....................................................................11
5.2.1 Select range for the input signal ....................................................................11
5.2.2 Set the decimal point for the actual value ....................................................11
5.2.3 Change the range limits ....................................................................................12
5.2.4 Scaling Slope ......................................................................................................13
5.3 Setting the Scaling Slope
5.3.1 Enter the number of Scaling points ................................................................14
5.3.2 Define first Scaling point ..................................................................................15
5.3.3 Define second Scaling point ...........................................................................15
5.3.4 Define further Scaling points ...........................................................................15
5.4 Totalizer
5.4.1 Setting the Input Threshold for the Totalizer ................................................15
5.4.2 Totalizer Setup ...................................................................................................16
5.4.2.1 Setting the decimal point for the totalizer ..................................18
5.4.2.2 Overall scaling for the total value ...................................................18
5.4.3 Resetting the Total value ..................................................................................19
5.5 Alarms/Alarm Outputs
5.5.1 Alarm 1/Output 1 ................................................................................................20
5.5.1.1 Alarm 1 off/on ..................................................................................20
5.5.1.2 Select threshold 1 .......................................................................... 20
5.5.1.3 Select mode for output threshold 1 ..............................................20
5.5.1.4 Hysteresis for threshold 1 ..............................................................21
5.5.1.5 Reset Latch signal at output 1 ......................................................22
5.5.1.6 Select signal form for output threshold 1 ...................................23
Page 2
5.5.2 Alarms 2/Output 2 ............................................................................................. 23
5.5.2.1 Alarm 2 off/on .................................................................................. 23
5.5.2.2 Select threshold 2 ........................................................................... 23
5.5.2.3 Select mode for output threshold 2 ............................................. 23
5.5.2.4 Reset Latch signal at output 2 ......................................................24
5.5.2.5 Reset Latch signal at output 2 ...................................................... 24
5.5.2.6 Select signal form for output threshold 2 ...................................25
5.6 MIN/MAX value acquisition ........................................................................................... 25
5.6.1 Maximum value monitoring .................................................................................. 25
5.6.1.1 Resetting the maximum value ...................................................... 25
5.6.2 Minimum value monitoring ..............................................................................25
5.6.2.1 Resetting the minimum value .................................................... 26
5.6.3 Effect of Overflow/Underflow for MIN/MAX value ..................................... 26
5.7 Mains Hum Filter ............................................................................................................. 26
5.9 Setting default value ....................................................................................................... 27
5.10 End of setup ...................................................................................................................... 27
5.11 Check/alter parameters ................................................................................................. 28
6. Operation .......................................................................................................................... 28
6.1 Switching over the display during operation ............................................................. 29
6.2 Setting the limits during operation ............................................................................... 30
6.3 Resetting the MIN/MAX value ...................................................................................... 30
6.4 Resetting the Totalizer .................................................................................................... 32
6.5 Display Hold ..................................................................................................................... 32
Page 3