Maintenance - Makita LS1040 Betriebsanleitung

Compound cutting
Compound cutting is the process in which a bevel angle
is made at the same time in which a miter angle is being
cut on a workpiece. Compound cutting can be performed
at angle shown in the table.
Bevel angle
45°
006389
When performing compound cutting, refer to "Press
cutting", "Miter cutting" and "Bevel cut" explanations.
Cutting aluminum extrusion (Fig. 31)
When securing aluminum extrusions, use spacer blocks
or pieces of scrap as shown in Fig. 31 to prevent
deformation of the aluminum. Use a cutting lubricant
when cutting the aluminum extrusion to prevent build-up
of the aluminum material on the blade.
CAUTION:
• Never attempt to cut thick or round aluminum
extrusions. Thick aluminum extrusions may come
loose during operation and round aluminum extrusions
cannot be secured firmly with this tool.
Wood facing (Fig. 32)
Use of wood facing helps to assure splinter-free cuts in
workpieces. Attach a wood facing to the guide fence
using the holes in the guide fence.
See Fig. 32 concerning the dimensions for a suggested
wood facing.
CAUTION:
• Use straight wood of even thickness as the wood
facing.
• Use screws to attach the wood facing to the guide
fence. The screws should be installed so that the screw
heads are below the surface of the wood facing.
• When the wood facing is attached, do not turn the turn
base with the handle lowered. The blade and/or the
wood facing will be damaged.
Cutting repetitive lengths (Fig. 33)
When cutting several pieces of stock to the same length,
ranging from 240 mm to 400 mm, use of the set plate
(optional accessory)
operation. Install the set plate on the holder (optional
accessory) as shown in Fig. 33.
Align the cutting line on your workpiece with either the
left or right side of the groove in the kerf board, and while
holding the workpiece from moving, move the set plate
flush against the end of the workpiece. Then secure the
set plate with the screw. When the set plate is not used,
loosen the screw and turn the set plate out of the way.
NOTE:
• Use of the holder-rod assembly (optional accessory)
allows cutting repetitive lengths up to 2,200 mm (7.2 ft.)
approximately.
Carrying tool
Make sure that the tool is unplugged. Secure the blade at
0° bevel angle and the turn base at left miter angle fully.
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. (Fig. 34)
Carry the tool by carrying grip as shown in Fig. 35. If you
remove the holders, dust bag, etc., you can carry the tool
more easily.
Miter angle
Left and Right 0° – 45°
will facilitate more
CAUTION:
• Always secure all moving portions before carrying the
tool.
• Stopper pin is for carrying and storage purposes only
and not for any cutting operations.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
WARNING:
• Always be sure that the blade is sharp and clean for the
best and safest performance.
Adjusting the cutting angle
This tool is carefully adjusted and aligned at the factory,
but rough handling may have affected the alignment. If
your tool is not aligned properly, perform the following:
Miter angle (Fig. 36)
Loosen the grip which secures the turn base. Turn the
turn base so that the pointer points to 0° on the miter
scale. Tighten the grip and loosen the hex bolts securing
the guide fence using the socket wrench.
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Square the side of the
blade with the face of the guide fence using a triangular
rule, try-square, etc. Then securely tighten the hex bolts
on the guide fence in the order from the right side.
(Fig. 37)
Bevel angle
0° bevel angle (Fig. 38 & 39)
Lower the handle fully and lock it in the lowered position
by pushing in the stopper pin. Loosen the lever at the
rear of the tool.
Turn the 0° bevel angle adjusting bolt on the right side of
the turn base two or three revolutions clockwise to tilt the
blade to the right. Carefully square the side of the blade
with the top surface of the turn base using the triangular
rule, try-square, etc. by turning the 0° bevel angle
adjusting bolt counterclockwise. Then tighten the lever
efficient
securely.
Make sure that the pointer on the turn base point to 0° on
the bevel scale on the arm. If it does not point to 0°,
loosen the screw which secures the pointer and adjust
the pointer so that it will point to 0°. (Fig. 40)
45° bevel angle
Adjust the 45° bevel angle only after performing 0° bevel
angle adjustment. To adjust left 45° bevel angle, loosen
the lever and tilt the blade to the left fully. Make sure that
the pointer on the arm points to 45° on the bevel scale on
the arm holder. If the pointer does not point to 45°, turn
the 45° bevel angle adjusting bolt on the left side of the
arm until the pointer points to 45°. (Fig. 41)
Replacing fluorescent tube (Fig. 42)
Only for model LS1040F / LS1040FS
CAUTION:
• Always be sure that the tool is switched off and
unplugged before replacing the fluorescent tube.
17