Care And Service - Kärcher FC 7 Cordless Originalbetriebsanleitung

Interrupting operation
ATTENTION
Damp rollers
Moisture damage to sensitive floors
To prevent damage to sensitive floors through wet roll-
ers, place the device in the parking station during longer
work breaks.
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Note
If the device is placed on the parking station without a
waste water tank, the unlocking button must be pressed
to remove the device.
Illustration AF
Ending operation
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Illustration AB
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
3. Clean the device (see Chapter Care and service).
Storing the device
ATTENTION
Liquids/moist dirt
Unpleasant odours can develop if the device contains
liquids/moist dirt when stored.
Completely empty the fresh water tank and waste water
tank before storing the device.
Use the cleaning brush to remove hair and dirt particles
from the hair filters in the floor head cover.
Allow the cleaned rollers to dry in the air, e.g. mounted
in the device on the parking station. Do not place the wet
rollers in an enclosed cupboard to dry.
1. Put the empty waste water tank in the cleaning sta-
tion to dry.
a Place the device on the parking station and let it
snap into place.
b Then place the device with the parking station on
the cleaning station.
Illustration AB
2. Fit the cleaned rollers on the device for drying.
Illustration AC
3. Charge the battery (see Chapter Charging pro-
cess).
4. Store the device in a dry room.
Illustration AE

Care and service

Floor head cleaning by a rinsing process
ATTENTION
Dirt or detergent residues
The waste water tank and the hair filters must be
cleaned regularly to ensure that dirt does not accumu-
late in the tank and hair filters. Dirt particles can clog the
hair filters and slots if the device is not cleaned after use.
The accumulation of dirt and bacteria can also result in
the development of unpleasant odours in the device.
On completion of work, place the device in the cleaning
station and start the rinsing process.
22
Clean the floor head in the cleaning station only by us-
ing the automatic rinsing process and not by pouring
water into the station separately. Make sure that the
waste water tank is attached.
Do not hold the underside of the floor head under water.
Note
The rinsing process cannot be started while the "MAX"
indicator (red) is lit and the waste water tank has not
been emptied.
Note
The LED lighting on the floor head remains switched off
during the rinsing process.
1. Press the ON/OFF switch.
The device switches off.
2. Empty the waste water tank and reinsert it (see
chapter Emptying the waste water tank).
3. Place the device with an empty waste water tank in
the parking station.
4. Fill the fresh water tank with at least 200 ml of fresh
water without a detergent or care agent (see chapter
Filling the fresh water tank).
Illustration P
Note
It is not necessary to add detergent for the rinsing pro-
cess.
5. Hold the ON/OFF switch and the cleaning level ad-
justment button simultaneously pressed for
3 seconds.
An acoustic signal sounds.
Illustration Q
6. The indicators light up repeatedly from top to bot-
tom.
The rinsing process starts and takes approx. 2 min-
utes.
Illustration R
Note
At the start of the rinsing process, the water runs from
the fresh water tank onto the rollers for approx. 80 sec-
onds. During this time the device is silent. Only at the
end of the rinsing process do the rollers start to turn for
approx. 30 seconds.
7. When the rinsing process is finished, a signal tone
sounds and the (red) "MAX" display lights up.
Illustration S
8. Press the unlocking button for the waste water tank
and place the device on the parking station. The
waste water tank remains in the cleaning station.
Note
The (red) "MAX" display flashes for 10 seconds if an at-
tempt is made to switch the device on again with a full
waste water tank.
Cleaning work cannot be continued.
9. Press the unlocking button for the hair filters in-
wards.
The hair filters are released.
10. Place the hair filters in the cleaning station.
Illustration U
11. Remove the rollers and place them in the cleaning
station.
Illustration V
12. Transport the cleaning station with waste water
tank, hair filters and rollers to the toilet, sink or waste
container as required.
Illustration W
13. Clean the waste water tank (see Chapter Cleaning
the waste water tank).
14. Clean the rollers (see Chapter Cleaning the rollers).
English