Scheppach DM600VARIO Original Bedienungsanleitung Seite 20

17. Avoid unintentional starting
- Ensure switch is in "off" position when plug-
ging in.
18. Use outdoor extension leads
- When the tool is used outdoors, use only ex-
tension cords intended for outdoor use and
so marked.
- Use the cable drum only in the unrolled state.
19. Stay alert
- m Watch what you are doing, use common
sense and do not operate the tool when you
are tired.
20. Check damaged parts
- Before further use of tool, it should be care-
fully checked to determine that it will operate
properly and perform its intended function.
- Check whether the moving parts are work-
ing properly and are not becoming jammed
or whether parts are damaged. All parts must
be correctly fitted and satisfy all conditions to
ensure the proper operation of the power tool.
- A guard or other part that is damaged should
be properly repaired or replaced by an au-
thorized service centre unless otherwise in-
dicated in this instruction manual.
- Have defective switches replaced by an au-
thorized service centre.
- Do not use any faulty or damaged connection
cables.
- Do not use the tool if the switch does not turn
it on and off.
21. Warning!
- The use of any accessory or attachment oth-
er than one recommended in this instruction
manual may present a risk of personal injury.
22. Have your tool repaired by a qualified person
- This electric tool complies with the relevant
safety rules. Repairs should only be carried
out by qualified persons using original spare
parts, otherwise this may result in considera-
ble danger to the user.
Warning! During operation, this power tool produces
an electromagnetic field. Under certain circumstanc-
es, this field may negatively affect active or passive
medical implants. In order to reduce the danger of
serious or fatal injuries, we recommend that individ-
uals who wear medical implants should consult their
doctor and the manufacturer of the implant before op-
erating the power tool.
Operational Safety Instructions for the Wood
Turning Lathe
• Familiarise yourself with the machine's features
and wood-turning techniques before using the ma-
chine.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
• Examine all workpieces for splits or knots. Glued
joints must set completely before turning.
• Ensure that the workpiece is securely locked in po-
sition and all attachments are secured.
• Before turning the machine ON ensure that the
workpiece can rotate freely by rotating it by hand.
• Keep your hands and fingers away from the rotat-
ing workpiece.
• Switch the machine OFF and wait until it has come
to a full stop before making any adjustments on the
workpiece, tailstock, or tool rest.
• Maintenance, adjustment, calibration and cleaning
may only be performed with the motor turned off.
• The machine is designed for use with wood-turning
chisels only.
• Always store away the wood-turning chisels safely
before you leave the workplace.
• Do not run the lathe without its covers and guards
in place.
• Keep cutting tools sharp.
• Use the lowest speed when starting a new work-
piece.
• Always stop the lathe at its slowest speed. If the
lathe is run so fast that it vibrates, there is a risk
that the workpiece will be thrown or the cutting tool
jerked from your hands.
• Do not allow cutting tools to bite into the workpiece.
The wood could be split or thrown from the lathe.
• Always position the tool rest above the centre line
of the lathe when shaping a piece of stock.
• Before attaching a workpiece to the face plate, al-
ways rough it out to make it as round as possible.
This minimizes the vibrations while the piece is be-
ing turned. Always fasten the workpiece securely
to the faceplate. Failure to do so could result in the
workpiece being thrown away from the lathe.
• Use a brush or compressed air to remove wood
shavings; never your hands. The wood shavings
will be sharp.
• The cutting tool must always be tight within the
chuck and adjusted to limit projection from the post.
This will reduce the possibility of the tool breaking
or bending.
• Do not reach a cross the lathe while it is running.
• Only feed workpiece into a cutting tool against the
direction of rotation. The workpiece must always be
rotating toward you.
• Do not leave the tool unattended when it is plugged
into an electrical outlet. Turn off the tool, and un-
plug it from its electrical outlet before leaving.
• This product is not a toy. Keep it out of reach of
children.
• Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities,
contains chemicals known to cause cancer, birth
defects or other reproductive harm. Some exam-
ples of these chemicals are:
- Lead from lead-based paints