Machine Specifications; Mechanical Hazards - Elektror SVD 8 Betriebs- Und Montageanleitung

CONTENTS
EN
1

MACHINE SPECIFICATIONS

2 INFORMATION ON TRANSPORT, HANDLNG AND
STORAGE OF THE MACHINE
3 INFORMATION ON PUTTING INTO SERVICE
4 INSTRUCTIONS FOR OPERATION AND USE
5 INSTRUCTIONS FOR MAINTENANCE
6 SAFETY RELATED INFORMATION ON
TAKING OUT OF OPERATION AND REMOVAL
7 LIABILITY AND EXCLUSION OF LIABILITY
8 DECLARATION OF INSTALLATION CONFORMITY
PURSUANT TO ANNEX II 1 B
9 TECHNICAL SPECIFICATIONS
10 BROKEN VIEW DRAWING
11 SPARE PARTS LIST
Operating staff must have access to these operating and
installation instructions at all times. Read carefully through
these operating and installation instructions before installing
the blower and putting it into service.
Specifi cations are subject to change. In case of doubt the
manufacturer should always be consulted. This document is
protected by copyright. It must not be disclosed to any third
party without our express permission in writing. Any form of
duplication or recording and storing in electronic form is pro-
hibited.
1 MACHINE SPECIFICATIONS
Please refer to the cover page for our full address details.
For details of the scope of validity of these operating and
installation instructions, please refer to the declaration of in-
corporation contained in annex II 1 B.
The specifi cations shown on page 19 are valid for serial
production. Your blower may deviate from these (refer to
the rating plate). In such a case, please observe the further
commonly valid documents included or the operating and in-
stallation instructions that then apply.
Rating plate
The data on the rating plate is the sole determining factor for
connection, maintenance and ordering of spare parts. The
unit's serial number and year of manufacture are also to be
found on the rating plate.
Typ
Mot. EN 60034-1
kW cos
Hz
1.1 Designated use
Elektror conveying blowers are equipped with impellers
made of steel sheet and with radial ending blades.
The conveying blowers are suitable for conveying plastic
granulate, plastic waste as well as light bulk material of all
kinds. It is not allowed to convey substances or mixtures of
substances which may pose special risks during the opera-
tion, e.g. combustible dusts, explosive substances, chemi-
cally unstable substances or mixtures of substances which
can react with one another.
12
D-73760 Ostfildern
Germany
Nr.
IP W-Kl.F
kW cos
min min Hz
-1 -1
V
A A
Operating and assembly instructions SVD
Use of the blowers for
• aggressive,
• abrasive,
• sticky,
• toxic,
• potentially explosive or
• very moist
media is not permissible.
The temperature of medium being conveyed must not fall
below -20°C or exceed +60°C.
The blower is not suitable for installation outdoors without
special measures. The blower is fundamentally designed for
S1 operation (continuous operation). However, a maximum
of 30 switching operations per hour are permitted.
The blower is not suitable for conveying, or installation in,
atmospheres that are potentially explosive.
Special versions for use outside the limits of the applications
described above are available upon request. Reconstruction
or modifi cation of the blower is not permissible. In the case
of special devices, the advice in the accompanying supple-
mentary operating and installation instructions must be noted
and adhered to. They deviate in certain places from these
operating and installation instructions.
A distinguishing feature of Elektror blowers is their high de-
gree of operational reliability. Since the blowers described
here are very powerful machines, the following safety in-
structions must be strictly observed to avoid injury or dam-
age to property or the blower itself.

1.2 Mechanical hazards

Mechanical hazards on Elektror blowers are kept to a minimum
in keeping with health and safety requirements and the state of
the art. To exclude any residual risks due to handling, we rec-
ommend that suitable protective gear is deployed or worn in all
phases of the unit's life (please observe the advice given below).
Warning!
Risk of injury from shearing/entanglement!
In special versions with temperature lock (1), the-
re is a risk of limbs being sheared and clothing/
hair becoming entangled.
Wear personal protective equipment, close-fi tting
clothing, and a hair net during all phases of the
device's life.
V
1.3 Hazards arising from reaching in and unexpected
start-up
When in operation, a high risk of injury exists from rotating parts
inside the unit. Before opening, reaching in or inserting tools into
the unit, always put it out of operation and wait until all moving
parts have come to a standstill. Ensure that the unit is reliably
secured against unintentional start-up for the entire duration.
Also make sure that a hazardous situation does not ensue
as a result of starting up after a period at standstill. For ex-
ample, after a power interruption or blockade has occurred.
SVD blowers may be supplied without wire mesh guards on
1
www.elektror.com