Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
CONTENTS
EN
1
MACHINE SPECIFICATIONS
2
3
INFORMATION ON PUTTING INTO SERVICE
4
5
6
7
8
9
BROKEN VIEW DRAWING
10 GENERAL SPARE PARTS LIST
11 TECHNICAL SPECIFICATIONS
12 INDICATIONS ACCORDING TO ERP IMPLEMENT-
ING REGULATION 327/2011
These Operating and Assembly Instructions should be avail-
able to operating personnel at all times. Read these Operat-
ing and Assembly Instructions carefully before installing and
putting the blower into service.
Subject to change without prior notice. If in any doubt, the
manufacturer should be consulted. This document is protect-
ed by copyright. It must not be disclosed to third parties with-
out our express written consent. Any form of duplication or
recording and storage in electronic equipment is forbidden.
1 MACHINE SPECIFICATIONS
Please refer to the cover sheet for our address.
For details of the scope of these Operating and Assembly
Instructions, please refer to the Declaration of Installation
Conformity pursuant to Annex II 1 B.
The technical specifi cations on page 21 apply to the stand-
ard version. Your blower's specifi cations may diff er from these
specifi cations (refer to nameplate). If this is the case, please
refer to the enclosed, additionally applicable documents or
your own applicable Operating and Assembly Instructions.
Nameplate
The data on the rating plate is applicable to connection, mainte-
nance and ordering of spare parts. Also refer to the rating plate for
the serial number of the appliance and its year of manufacture.
Typ
Mot. EN 60034-1
kW cos
Hz
1.1 Designated use
The blowers are exclusively designed for conveying gase-
ous media without solids.
Any solid matter or impurities in the medium to be conveyed
must be fi ltered out before they enter the blower. We recom-
mend a condensed water borehole at the lowest point in the
housing in the event of the formation of condensation.
Use of the blowers for
• aggressive,
• abrasive,
• sticky,
• toxic,
10
D-73760 Ostfildern
Germany
Nr.
IP
W-Kl.F
kW cos
min
min
Hz
-1
-1
V
A
A
Operating and assembly instructions A-HP
• potentially explosive or
• very moist
media is not permissible.
The maximum temperature of the conveyed medium must
not exceed -20°C to +80°C in the standard version and
180°C in special versions fi tted with a thermal barrier. Solid
particles or contaminants must be removed by a fi lter unit
before entering the blower.
Series connection or parallel connection of fans is only pos-
sible after consultation with Elektror.
The blower is not suitable for installation outdoors without
special measures.The blower is fundamentally designed for
S1 operation (continuous operation). However, a maximum
of 30 switching operations per hour are permitted.
Special versions for applications not mentioned above are
available on request. Remodelling and modifi cation of the
blower are not permitted. In the case of special equipment,
the enclosed supplementary Operating and Assembly In-
structions must be observed and adhered to. The supple-
mentary instructions diff er in certain respects from these Op-
erating and Assembly Instructions.
Elektror blowers off er a high level of operational reliability.
As the blowers are high-powered machines, the safety in-
structions must be strictly observed in order to avoid injuries,
damage to objects and to the machine itself.
1.2 Mechanical hazards
The mechanical hazards in Elektror blowers have been mini-
mised in accordance with the current state of the art, as well as
the requirements for safety and health protection. To eliminate
any further risk on the part of the operator, we recommend that
suitable protective gear be used and worn during all lifecycle
phases of the appliance (please refer to the instructions below).
1.3 Hazards arising from reaching in and unexpected
start-up
The rotating parts inside the appliance pose a high risk of in-
jury during operation. Before opening, reaching in or inserting
tools into the appliance, always shut it down and wait until all
moving parts come to a standstill. Make sure the appliance is
reliably protected against restarting while work is in progress.
Also make sure that no hazardous situation can occur as a
consequence of restarting after shutdown, e.g. as a result of
a power cut or blockage.
1.4 Weight and stability
Beware of falling hazards during transportation and installa-
tion in particular. Refer to 2.1 - Transportation and handling,
as well as 3.2 - Installation and assembly.
1.5 Suction eff ect
Warning!
Risk of injury due to suction eff ect!
V
Objects, clothing and hair can be sucked in at the
intake port.
The operator is required to wear a hairnet and
tight-fi tting clothing.
Do not stay near the suction opening during
operation!
1.6 Blowing eff ect
Warning!
Risk of injury due to strong blow-out eff ect of the
medium and ejected parts!
Impurities, debris and impermissible media may
cause objects to be thrown out of the fan outlet at
high speed!
Make sure that the fan delivers only clean air!
1
2
www.elektror.com
Werbung
Kapitel
Inhaltsverzeichnis
