Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operating and assembly instructions SD
CONTENT
1 MACHINE SPECIFICATIONS
EN
3 INFORMATION ON PUTTING INTO SERVICE
9 TECHNICAL SPECIFICATIONS
10 BROKEN VIEW DRAWING
11 GENERAL SPARE PARTS LIST
These Operating Instructions must be available to operating
personnel at all times. Read these Operating and Assembly
Instructions carefully before installing and putting the side
channel blower into service.
Subject to change without prior notice. If in any doubt, the
manufacturer should be consulted. This document is protect-
ed by copyright. It must not be disclosed to third parties with-
out our express written consent. Any form of duplication or
recording and storage in electronic equipment is forbidden.
1 MACHINE SPECIFICATIONS
Please refer to the cover sheet for our address.
For the area of validity of these Operating and Assembly In-
structions, please refer to the Declaration of Installation Con-
formity contained in Annex II 1 B.
The technical specifi cations on pages 20-25 apply to the
standard version. Your side channel blower's specifi cations
may diff er from these specifi cations (refer to nameplate). If
this is the case, please refer to the enclosed, additionally ap-
plicable documents or your own applicable Operating and
Assembly Instructions.
10
Nameplate
The data on the rating plate is applicable to connection,
maintenance and ordering of spare parts. Also refer to the
nameplate for the serial number of the appliance and its year
of manufacture.
Typ
Mot. EN 60034-1
kW cos
Hz
1.1 Designated use
Operation of the side channel blower is only permissible
within the limits specifi ed on the nameplate. The information
in the following sections must be noted and observed.
The side channel blowers are exclusively designed for con-
veying gaseous media without solids. Any solid matter or im-
purities in the medium to be conveyed must be fi ltered out
before they enter the side channel blower.
Use of the blowers for
• aggressive
D-73760 Ostfildern
Germany
Nr.
IP
W-Kl.F
kW cos
min
-1
min
-1
Hz
V
A
A
• abrasive
• sticky
• toxic
• potentially explosive or
• very moist
media is not permissible.
The permissible conveyed medium temperature for the
standard version is -20 °C to +40 °C. Solid particles or con-
taminants must be removed by a fi lter unit before entering
the side channel blower.
The blower is not suitable for installation outdoors without
special measures. The blower is fundamentally designed for
S1 operation (continuous operation). However, a maximum
of 30 switching operations per hour are permitted.
The standard version of the blower is not suitable for use in
explosive atmospheres.
Special versions for applications not mentioned above are
available on request. Remodelling and modifi cation of the
blower are not permitted. In the case of special equipment,
the enclosed supplementary Operating and Assembly In-
structions must be observed and adhered to. The supple-
mentary instructions diff er in certain respects from these Op-
erating and Assembly Instructions.
Elektror blowers off er a high level of operational reliability.
As the blowers are high-powered machines, the safety in-
structions must be strictly observed in order to avoid injuries,
damage to objects and to the machine itself.
1.2 Mechanical hazards
The mechanical hazards in Elektror side channel blowers
have been minimised in accordance with the current state
of the art, as well as the requirements for safety and health
protection. To eliminate any further risk on the part of the op-
erator, we recommend that suitable protective gear be used
and worn during all lifecycle phases of the appliance (please
refer to the instructions below).
1.3 Danger of hand injury
The rotating parts inside the appliance pose a high risk of
injury during operation. Before opening, reaching in or insert-
ing tools into the appliance, always shut it down and wait
until all moving parts come to a standstill. Make sure the ap-
pliance is reliably protected against restarting while work is
in progress.
Also make sure that no hazardous situation can occur as a
consequence of restarting after shutdown, e.g. as a result of
a power cut or blockage.
1.4 Weight and stability
Beware of falling hazards during transportation and installa-
tion in particular. Refer to 2.1 - Transportation and handling,
as well as 3.2 - Installation and assembly.
1.5 Suction eff ect
V
The side channel blowers produce a powerful suction eff ect.
Warning!
Objects, items of clothing and also hair can be
sucked into the intake port. Risk of injury!
Do not stand near the intake opening during op-
eration. The blower must not under any circum-
stances be operated with the intake port open,
and should, therefore, be covered with a wire
guard in conformity with DIN EN ISO 13857
(danger of injury from impeller!)
www.elektror.com
Werbung
Kapitel
Inhaltsverzeichnis
