Direkte Zugregelung - ABB DCS550 Handbuch

Direkte Zugregelung

Die direkte Zugregelung (Regelung über Kraftmessdose) ist eine Zugregelung mit Rückführung. Der
Zugistwert wird mit einer Kraftmessdose gemessen und über einen Analogeingang (AI3) und PID-Regler in
Gruppe 40 verwendet. Der Drehzahlregler bleibt aktiv, ist aber in Sättigung. Folgende Parameter werden
eingestellt, wenn WinderMacro (61.01) = DirectTens gesetzt ist:
Parametername
Ref1Sel (11.03)
TorqMaxSPC (20.07)
TorqMinSPC (20.08)
IndepTorqMaxSPC (20.24)
IndepTorqMinSPC (20.25)
SpeedCorr (23.04)
SpeedRefScale (23.16)
TorqSel (26.01)
TorqMuxMode (26.04)
LoadComp (26.02)
KpPID (40.01)
TiPID (40.02)
PID Act1 (40.06)
PID Ref1 (40.13)
PID OutMin (40.16)
PID OutMax (40.17)
PID OutDest (40.18)
PID ReleaseCmd (40.23)
WriteToSpdChain (61.02)
WindUnwindCmd (61.04)
TopBottomCmd (61.05)
WinderOnCmd (61.06)
TensionOnCmd (61.07)
WindSpdOffset (61.14)
DiaLineSpdIn (62.01)
DiaMotorSpdIn (62.02)
DiameterSetCmd (62.04)
AdaptKpDiaActIn (62.10)
AdaptKpOutDest (62.13)
AccActIn (62.17)
InerDiaActIn (62.23)
InerAccActIn (62.24)
InerReleaseCmd (62.28)
TensRefIn (63.01)
TaperDiaActIn (63.02)
TensValueIn (63.03)
TensSetCmd (63.04)
TensRampHoldCmd (63.09)
TensPulseCmd (63.13)
TTT Ref1In (63.18)
TTT Ref2In (63.19)
TTT Ref3In (63.20)
TTT DiaActIn (63.22)
FrictMotorSpdIn (63.31)
FrictReleaseCmd (63.32)
Add1OutDest (64.01)
Add1In1 (64.02)
Add1In2 (64.03)
Add1ReleaseCmd (64.04)
Add2OutDest (64.08)
Add2In1 (64.09)
Add2In2 (64.10)
Add2ReleaseCmd (64.11)
DirectTens
AI1
120 %
-120 %
325 %
-10 %
0 rpm
100 %
Speed
TorqSel2601
0 %
1
1000
517 = AI3 ValScaled (5.17)
6315 = TensionRef (63.15)
-10 %
10 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
DI1
Auto
150 rpm, connected to SpeedCorr (23.04)
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
DI2
6208 = DiameterAct (62.08)
2403 = KpS (24.03)
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
516 = AI2 ValScaled (5.16)
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
309 = PID Out (3.09)
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
2024 =IndepTorqMaxSPC (20.24)
6324 = TensToTorq (63.24)
0
Auto
2602 = LoadComp (26.02)
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto
3ADW000379R0503 DCS550 Handbuch d e
Werkseinstellung (Standard)
SpeedRef2301
325 %
-325 %
325 %
-325 %
0 rpm
100 %
Speed
TorqSel2601
0 %
5
2500
0
0
-100 %
100 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
Auto
Auto
0
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
NotUsed
6208 = DiameterAct (62.08)
0
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
0
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
0
6324 = TensToTorq (63.24)
0
Auto
0
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto
149
Wickler