Geschwindigkeitsregelung - ABB DCS550 Handbuch

Geschwindigkeitsregelung

Die Geschwindigkeitsregelung berechnet den Coildurchmesser und den Motordrehzahlsollwert. Mit Hilfe des
Durchmessers kann der Drehzahlregler an alle Coildurchmesser angepasst werden. Der Zug wird nicht geregelt.
Folgende Parameter werden eingestellt, wenn WinderMacro (61.01) = VelocityCtrl gesetzt ist:
Parametername
Ref1Sel (11.03)
TorqMaxSPC (20.07)
TorqMinSPC (20.08)
IndepTorqMaxSPC (20.24)
IndepTorqMinSPC (20.25)
SpeedCorr (23.04)
SpeedRefScale (23.16)
TorqSel (26.01)
TorqMuxMode (26.04)
LoadComp (26.02)
KpPID (40.01)
TiPID (40.02)
PID Act1 (40.06)
PID Ref1 (40.13)
PID OutMin (40.16)
PID OutMax (40.17)
PID OutDest (40.18)
PID ReleaseCmd (40.23)
WriteToSpdChain (61.02)
WindUnwindCmd (61.04)
TopBottomCmd (61.05)
WinderOnCmd (61.06)
TensionOnCmd (61.07)
WindSpdOffset (61.14)
DiaLineSpdIn (62.01)
DiaMotorSpdIn (62.02)
DiameterSetCmd (62.04)
AdaptKpDiaActIn (62.10)
AdaptKpOutDest (62.13)
AccActIn (62.17)
InerDiaActIn (62.23)
InerAccActIn (62.24)
InerReleaseCmd (62.28)
TensRefIn (63.01)
TaperDiaActIn (63.02)
TensValueIn (63.03)
TensSetCmd (63.04)
TensRampHoldCmd (63.09)
TensPulseCmd (63.13)
TTT Ref1In (63.18)
TTT Ref2In (63.19)
TTT Ref3In (63.20)
TTT DiaActIn (63.22)
FrictMotorSpdIn (63.31)
FrictReleaseCmd (63.32)
Add1OutDest (64.01)
Add1In1 (64.02)
Add1In2 (64.03)
Add1ReleaseCmd (64.04)
Add2OutDest (64.08)
Add2In1 (64.09)
Add2In2 (64.10)
Add2ReleaseCmd (64.11)
VelocityCtrl
AI1
325 %
-325 %
325 %
-325 %
0 rpm
100 %
Speed
TorqSel2601
0 %
5
2500
0
0
-100 %
100 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
DI1
Auto
0
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
DI2
6208 = DiameterAct (62.08)
2403 = KpS (24.03)
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
0
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
0
Auto
0
6324 = TensToTorq (63.24)
0
Auto
0
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto
3ADW000379R0503 DCS550 Handbuch d e
Werkseinstellung (Standard)
SpeedRef2301
325 %
-325 %
325 %
-325 %
0 rpm
100 %
Speed
TorqSel2601
0 %
5
2500
0
0
-100 %
100 %
0
Auto
Auto
WindCtrlWord
WindCtrlWord
Auto
Auto
0
202 = SpeedRef2 (2.02)
104 = MotSpeed (1.04)
NotUsed
6208 = DiameterAct (62.08)
0
216 = dv_dt (2.16)
6208 = DiameterAct (62.08)
6221 = AccActAdjust (62.21)
Auto
0
6208 = DiameterAct (62.08)
0
Auto
RelTensRamp
Auto
0
6315 = TensionRef (63.15)
0
6208 = DiameterAct (62.08)
104 = MotSpeed (1.04)
Auto
0
6324 = TensToTorq (63.24)
0
Auto
0
6230 = InertiaComp (62.30)
6334 = FrictionComp (63.34)
Auto
145
Wickler