Maintenance, Cleaning, Repair; Ordering Replacement Parts - EINHELL BT-LC 500 Originalbetriebsanleitung

Anleitung_BT_LC_500_SPK7__ 07.05.12 07:13 Seite 18
GB
the saw blade cover (3).
Do not apply so much pressure to the feed
n
carriage that the motor speed falls.
After the cut has been completed return the
n
carriage completely to its initial position.
Remove the saw wood from the carriage.
n
To turn the saw off again, press the red button "0".
n
Important: Never switch on the machine again
whilst it is slowing down.
Note: If the wood cannot be sawn completely in a
n
single cut, turn it over (reversing cut). To do this
return the feed carriage to its initial position, turn
the wood along the cut and saw through it again.
Important: If the saw blade (4) does not reach a
n
standstill after a maximum of 10 seconds, have the
brake checked by an authorized specialist and
replaced if necessary.
Pull the power plug immediately after finishing
n
work. Never leave the machine until you have
pulled the plug and secured the machine to
prevent its unauthorized use.
7.2. Changing the saw blade (Fig. 12-16)
Important: Pull the power plug!
Allow the saw blade to cool before you change it.
Do not use inflammable liquids to clean the saw
blade.
Always wear gloves when handling saw blades.
Risk of injury!
Remove the screw (15) from the cover plate (16)
n
and pull the cover plate downwards.
Self locking nut (H) should be loosened if the
n
seesaw position is open (if splint (9) is taken off).
Remove the cross bolts (E) and washers (F,G). The
moveable work frame (6) can now be completely
opened. After removing the screws, take off the
attached saw blade cover (2) sideways. Hold the
drive shaft securely with a wrench.
Loosen the flange screw (18) in a counter-
n
clockwise direction.
Remove the flange screw (18) and external flange
n
(19) from the saw shaft (20).
Now the saw blade (4) can be removed from the
n
saw shaft (20)
Carefully clean the saw blade (4), external flange
n
(19) and flange screw (18) before assembly.
To reassemble new saw blades, proceed in the
n
reverse order and re-tighten the flange screw (18).
Important: Do not try to secure the flange screw by
hitting the tool and do not use tool extensions!
Make sure the rotation of the saw blade (4) is in the
correct direction.
Attach the saw blade cover (16), cover plate and
n
spring mechanism.
Important: Tools must again be separated from the
n
flange screw!
18
7.3. Transport (Fig. 6,17)
The chassis means that the saw can be transported
by a single person.
7.4. Overload cut-out (Fig. 14)
The motor of this equipment is protected against
overload by an overload switch (A). If the rated current
is exceeded, the overload switch (A) shuts down the
equipment.
Let the equipment cool down for several minutes.
n
Press the overload switch.
n
Press the green button "I" to switch on the
n
equipment.

8. Maintenance, cleaning, repair

Caution: Pull out the power plug first.
Remove dust and dirt regularly from the machine. Use
a hand brush or cloth for this. Test the saw blade
regularly for signs of wear. During longer periods of
standstill, the saw blade, the spring mechanism (8)
and the mount (17) of the moveable work frame
should be lightly oiled.
Blunt saw blades must be sharpened. Clean
resinified saw blades.
Check that all screw connections are secure at
regular intervals.
Keep the handles dry and free of resin, oil and
grease at all times. Never use caustic cleaning
products for cleaning purposes.
The saw must be covered with a tarpaulin if it is left
in unprotected areas or in outdoors. It is particularly
important to protect the motor and switch from water
contact.
Important: Repairs to electric tools may only be
carried out by a trained electrician.

9. Ordering replacement parts

Please quote the following data when ordering
replacement parts:
Type of machine
n
Article number of the machine
n
Identification number of the machine
n
Replacement part number of the part required
n
For our latest prices and information please go to
www.isc-gmbh.info