Technical Specifications - Maxitrol GV60 Installations- Und Bedienungsanleitung

INSTALLATION INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Gas combination control according to CSA or CE ap-
proval (see label for certification)
FUELS
CSA: Suitable for natural, manufactured, mixed gases,
liquefied petroleum gases, and LP gas-air mixtures.
CE: Suitable for use with gases of EN 437 gas family 1,
2 and 3.
APPROVALS
CSA: Multifunctional gas control according to ANSI Z21.78
6.20 and ANSI Z21.20 6.20 for U.S. & Canada
CE: Gas Appliances Regulation 2016/426/EU and DIN EN
298, DIN EN 126, DIN EN 13611, 2014/53/EU (RED)
Infrared handset: GADAC Guidance Sheet B12
PRESSURE DROP/CAPACITY
CSA: 1" W.C. at 65,000 BTU/hr
CE: 2.5 mbar at 1.2 m³/h air
RANGE OF REGULATION
CSA: 10,000 to 85,000 BTU/hr
CE: Class C according EN 88
REGULATOR ADJUSTMENT
CSA: 3" W.C. to 5" W.C. (7.5 to 12.5 mbar); 8" W.C. to 12"
W.C. (20 to 30 mbar)
CE: 5 to 40 mbar
CE+CSA: 3" W.C. to 12" W.C. (7.5 to 30 mbar)
Convertible Regulator: 3 to 4.5" NG/8.5 to 11.5" LP
MOUNTING POSITION
Mount valve 0° to 90°, in any direction (including vertically)
from the upright position of the gas control knob.
MAXIMUM INLET PRESSURE
CSA: ½ psi (34.5 mbar)
CE: 50 mbar (20" W.C.)
MAIN GAS CONNECTION
CSA: ⅜ in. NPT; Rp ⅜ ISO 7-1 internal thread for 12 mm,
10 mm, 8 mm, 6 mm outside diameter tube.
CE: Rp ⅜ ISO 7-1 internal thread for 12 mm, 10 mm,
8 mm, 6 mm outside diameter tube.
INLET AND OUTLET CONNECTION
Side or Bottom
MAXIMUM ALLOWED TORQUE INLET AND OUTLET
CSA: 280 inch-pounds
CE: 35 Nm
PILOT GAS CONNECTION
CSA: 7/16-24 UNS for ¼" or ⅜ " tubing
CE: M10x1 for 4 mm or 6 mm tubing
THERMOCOUPLE/INTERRUPTER BLOCK
11/32-32 UNS, M10x1, M9x1, M8x1
AMBIENT TEMPERATURE RANGE
Combination control: 32 °F to 176 °F (0 °C to 80 °C)
Latching solenoid valve: 32 °F to 176 °F (0 °C to 80 °C)
Receiver RF without batteries: 176 °F (80 °C)
Receiver RF with batteries: 131 °F (55°C)
16
Receiver infrared with/without batteries: 131 °F (55°C)
Handset: 131 °F (55 °C)
Wall switch/Touchpad: 176 °F (80 °C)
Switch panel: 221 °F (105 °C)
Module: 176 °F (80 °C)
Ignition cable: 302 °F (150 °C)
Misc. cables: 221 °F (105 °C)
Infrared sensor: 176 °F (80 °C)
Cable with relay: 158 °F (70 °C)
POWER CONSUMPTION
See document "GV60-DS-EN..PCG" at mertikmaxtirol.com/litera-
ture under "GV Series Gas Control Systems".
HANDSETS
NOTICE
The handsets, receivers, wall switches, switch panels and
touchpads are not interchangeable with previous electronics.
RADIO FREQUENCY
CSA: 315 MHz for U.S. and for Canada.
For FCC ID:
a) User Information acc. to FCC15.21: Changes or
modifications not expressly approved by the party
responsible for compliance could void the user's
authority to operate the equipment.
For Canada - IC:
Statement acc. RSS Gen Issue 3, Sect. 7.1.3
This device complies with Part 15 of the FCC Rules
and with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two
conditions: (1) this device may not cause harmful in-
terference, and (2) this device must accept any in-
terference received, including interference that may
cause undesired operation.
CE: 433.92 MHz for Europe
Compliant with the EU-Radio Equipment Directive 2014/53/
EU (RED).
BATTERIES
Handset:
1 x 9 V, new design 2012: 3 x 1.5 V „AAA"
Receiver:
4 x 1.5 V "AA"
An AC Mains Adapter may be used instead of batteries.
(Alkaline recommended)
NOTICE
Only the Mertik Maxitrol AC Mains Adapter or one
preapproved by Mertik Maxitrol can be used. Use of other
adaptors can render the system inoperable.
V MODULE
CSA: Inlet: 115 VAC/60 Hz; 210 VA
Outlet: 115 VAC/60 Hz; 100 VA
Built-in fuse: 2.5 A
CE: Inlet: 230 VAC/50 Hz; 210 VA
Outlet: 230 VAC/50 Hz; 100 VA
Built-in fuse 2,5 A
LOCATION
Locate the combination gas valve where it is not exposed
to steam cleaning, high humidity, dripping water, corrosive
chemicals, dust or grease accumulation, or excessive heat.
4 / 20
FOR OEM USE ONLY