Yamaha AW16G Bedienungsanleitung Seite 205

3.1.9. Program Change Mode
Enable/disable reception and transmission. If MIDI Rx Ch is set to
ALL, these messages will be received regardless of their MIDI chan-
nel.
3.1.10. Control Change Mode
If this is enabled, you can specify the correspondence between con-
trol numbers and operations of the mixer section. For mode 1, trans-
mission and reception will occur without regard to the MIDI Tx Ch
and MIDI Rx Ch settings. For modes 2 and 3, reception will occur
without regard to MIDI channel if you set MIDI Rx Ch to ALL.
3.2. MIDI BULK DUMP
Controls transmission of Bulk Dump and Bulk Dump Request.
3.2.1. BULK DUMP Category
Selects the type of parameters for Dump or Dump Request.
3.2.1.1. SCENE
Mixer scene settings. E.BUF is the current state, 01-96 are stored
scenes. ALL selects all scenes.
3.2.1.2. LIBRARY
All memory settings for all libraries (EQ / EFFECT / DYNAMICS /
CHANNEL).
3.2.1.3. SYSTEM
Settings that apply to the entire AW16G.
3.2.1.4. REMOTE
Settings for the MIDI Remote function.
3.2.1.5. PROGRAM CHANGE TABLE
This is the Program Change Table.
3.2.1.6. ALL
All of the above settings.
3.2.2. INTERVAL
Specifies the interval at which consecutive Bulk Dump or Bulk
Dump Request messages will be transmitted. Increase this setting if
the receiving device fails to receive all of the bulk data.
3.2.3. RX DISABLE
If RX Disable is turned on, no Bulk Dump or Bulk Dump Request
messages will be received.
3.2.4. REQUEST
Transmits the selected Bulk Dump Request.
3.2.5. TRANSMIT
Transmits the selected Bulk Dump.
3.3. MIDI PROGRAM CHANGE TABLE
This table allows you to freely specify the correspondence between
Program Change No. and Scene No.
This table is used for conversion for both transmission and recep-
tion.
4. MIDI format list
4.1. CHANNEL MESSAGE
Command Rx/Tx
8n NOTE OFF Rx
9n NOTE ON Rx
Bn CONTROL CHANGE Rx/Tx
Cn PROGRAM CHANGE Rx/Tx
4.2. SYSTEM COMMON MESSAGE
Command Rx/Tx
F1 MIDI TIME CODE Rx/Tx
F2 SONG POSITION POINTER Tx
4.3. SYSTEM REALTIME MESSAGE
Command Rx/Tx
F8 TIMING CLOCK Tx
FA START Tx
FB CONTINUE Tx
FC STOP Tx
FE ACTIVE SENSING Rx
FF RESET Rx
4.4. SYSTEM EXCLUSIVE MESSAGE
4.4.1. REALTIME SYSTEM EXCLUSIVE
4.4.1.1. MMC
Command Rx/Tx
01 STOP Rx/Tx
02 PLAY Rx
03 DEFERRED PLAY Rx/Tx
04 FAST FORWARD Rx/TX
05 REWIND Rx/Tx
06 RECORD STROBE Rx
07 RECORD EXIT Rx
0F RESET Rx/Tx
44 LOCATE Rx/Tx
4.4.2. BULK DUMP / BULK DUMP REQUEST
Data Name Rx/Tx
'M' Rx/Tx Scene Memory & Request
'S' Rx/Tx System Memory & Request
'R' Rx/Tx Remote Memory & Request
'Q' Rx/Tx Equalizer Library & Request
'Y' Rx/Tx Dynamics Library & Request
'E' Rx/Tx Effect Library & Request
'H' Rx/Tx Channel Library & Request
'P' Rx/Tx Program Change Table & Request
function
Control the internal effect
Control the internal effect
Edit parameters
Switch scene memories
function
MTC transmission
Song position transmission
function
MIDI Clock transmission
Start command transmission
Continue command transmission
Stop command transmit
Check MIDI cable connections
Clear running status
function
Transport stop
Transport play
Transport play
Transport fast-forward
Transport rewind
Transport punch-in record
Transport punch-out
MMC reset
Transport locate
function
205