Vitek VT-1455 BK Die Betriebsanweisung Seite 5

BEFORE USING THE UNIT
After unit transportation or storage at low tempera-
ture it is necessary to keep it for at least two hours
at room temperature before switching on.
–
Unpack the blender set and remove any stickers
that can prevent unit operation.
–
Check the unit for damages; do not use it in case
of damages.
–
Before using the unit wash the blender attachment
(6), whisk (8), measuring cup (9), bowls (12 and
18), chopping knives (11 and 16), grating attach-
ment (19), slicing attachment (20), disc holder (21)
and pusher (13) with warm water and a neutral de-
tergent, then rinse and dry them.
–
Wipe the motor unit (4), whisk gear (7) and geared
lids (10 and 14) with a soft slightly damp cloth, then
wipe them dry.
–
Before switching the unit on make sure that your
home mains voltage corresponds to unit operat-
ing voltage.
Attention!
–
Do not immerse the motor unit (4), the whisk
gear (7), the geared lids (10 and 14), the power
cord and plug into water or any other liquids.
–
Do not put the attachments and bowls in a dish-
washing machine.
Selection of attachment rotation speed
–
To select the attachment rotation speed press and
hold the button (2) and rotate the speed control
knob (1).
–
To increase the attachment rotation speed turn the
knob (1) clockwise, and to reduce the attachment
rotation speed turn the knob (1) counterclockwise.
–
For operation at the maximal rotation speed, press
and hold the turbo mode "T" button (3).
Continuous operation time
The blender set allows quick and effective operation, but
continuous operation time should not exceed 1 minute
while using blender attachment (6), whisk (8), grating
attachment (19) and slicing attachment (20) and 30
seconds while using chopping knives (11,16). Make at
least a three-minute break between operation cycles.
USING THE BLENDER ATTACHMENT (6) (pic. 1).
The blender attachment (6) is used for chopping prod-
ucts, mixing or beating various ingredients.
WARNING: Before assembling the blender make
sure that the power plug is not inserted into the
socket.
–
Attach the blender attachment (6) to the motor unit
(4) till the release buttons (5) click.
–
Insert the plug into the mains socket. The blender is
ready for operation.
–
Immerse the blender attachment (6) into the bowl
with products, that you want to chop or mix; you can
use the measuring cup (9) for it.
–
Press and hold the on button (2), select the required
rotation speed of the blender attachment chopping
knife by turning the speed control knob (1) or press
and hold the turbo mode (3) "T" button.
VT-1455_IM.indd 5
Notes:
–
Products should be put into the bowl before switch-
ing the unit on.
–
Before you start to chop/mix, we recommend to
peel fruit and vegetables, remove inedible parts,
such as stones, and cut fruit or vegetables into ap-
proximately 2х2 cm cubes.
–
While using the blender attachment (6), hold the
unit vertically, try not to diverge from the vertical
plane (pic. 1).
–
After you finish using the unit, take the power plug
out of the socket and detach the blender attach-
ment (6) by pressing the release buttons (5).
Attention!
–
Do not remove the blender attachment (6) dur-
ing blender operation.
–
In order not to damage the blades, do not pro-
cess too hard products such as cereals, rice,
coffee, ice, frozen foods.
–
Continuous operation time should not exceed
1 minute with subsequent 3 minutes break at
least.
USING THE WHISK (8) (pic. 2).
Use the whisk (8) only to make cream, biscuit dough or
mixing ready desserts.
WARNING: Before assembling the blender make
sure that the power plug is not inserted into the
socket.
–
Insert the whisk (8) into the gear (7).
–
Attach the gear (7) to the motor unit (4) till the re-
lease buttons (5) click.
–
Insert the plug into the mains socket.
–
Put the whisk (8) into the bowl with products.
–
Press and hold the ON button (2), select the re-
quired whisk rotation speed by turning the speed
control (1) or press and hold the turbo mode "T"
button (3).
–
After you finish using the unit, take the plug out of
the socket, detach the whisks (8) from the gear (7),
and detach the gear (7) from the motor unit (4) by
pressing the buttons (5).
Attention!
–
Do not use the whisk (8) to make tight dough.
–
Products should be put into the bowl before
switching the unit on.
–
Continuous operation time should not exceed
1 minute with subsequent 3 minutes break at
least.
USING THE CHOPPER (pic. 3).
The chopper is used to chop small amount of meat,
hard cheese, onion, herbs, garlic, carrots, walnuts,
almonds or fruits.
Attention! Do not use the chopper to chop very
hard products, such as nutmegs, ice, coffee beans
or cereals.
Before you start chopping:
•
Cut meat, cheese, onion, garlic, carrots into ap-
proximately equal slices.
5
ENGLISH
31.05.2013 16:40:02