Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Gewicht
Zul. Antriebsdrehzahl bis
Für Biegsame Welle Typ NA 12
4.6 FH 15 - Gerades Handstück
Aufnahmebohrung Typ G35
Spannzangen bis (siehe Katalog)
Gewicht
Zul. Antriebsdrehzahl bis
Für Biegsame Welle Typ NA 12
Für Biegsame Welle Typ NA 15
Maschinenelemente
1 Spindel
4 Spannzange
2 Schlüssel
5 Spannset FDv 12-...
3 Überwurfmutter
6 Spannset FDv 12-...
Read the enclosed safety instructions appendix 39 230 ..!
Erection instructions appendix 39 328 ..!
1.
ROTOmaster
2.
Flexible shaft
3.
Start-up procedures:
3.1 Set the operating speed
3.2 Connect the flexible shaft
3.3 Connect the SAK safety clutch
3.4 Connect toolholders
3.5 Start-up with SAK
4.
Accessories: FH12, FH15, FALM, FSM, SAM, TAM
1.
ROTOmaster Type 12, Type 15
Constructions
TM=Base plate, STM=Trolley mounted, HM=Hanging attachment
Machine elements
A1 On/Off switch
A2 Motor shaft
Technical data
Three-phase motor
Type 12, 3-Ph Power Input / Output
Type 15, 3-Ph Power Input / Output
Protection class
Type of protection
Voltage (see spare parts list)
Ground fault protection: Use for tools
with water feed or in humid environments
No load speeds
- Standard
- Option
Sound pressure level CEN/TC 255 N
Type 12 Flexible shaft connection DIN10 = M10
For flexible shaft type NA12 DIN10 / G28
Type 15 Flexible shaft connection DIN15 = M14
For flexible shaft type NA12 DIN15 / G35
For flexible shaft type NA15 DIN 5 / G35
Vibration values ISO / DIS 8662-4
Toolholder type
Test plate
TALM 1:1
ø100 x 25
TAM 1:1
ø100 x 25
FSM 1:1
ø180 x 6
SAM 1:1
ø230 x 6
FH12
ø100 x 25
FH15
ø100 x 25
4
0,51 kg
15'000 min
DIN 10 / G28
(Abb. I)
ø 35 mm
ø 12 mm
0,23 kg
10'000 min
DIN 15 / G35
DIN 15 / G35
7 Spannschraube
8 Adapter zu BSK
9 6kt.-Schlüssel
GB
(Fig. A)
1'000 / 750 Watt
1'500 / 1'150 Watt
IP 44
various V
45 V
50 / 60 Hz
3'000 / 3'600 min
1'500 / 1'800 min
< 70 / < 70 dB( A )
see A2
see B2 B8
see A2
see B2 B8
Measured value
Speed
< 2,5 m/s2
3'600 min
< 2,5 m/s2
3'600 min
< 2,5 m/s2
3'600 min
< 2,5 m/s2
3'600 min
< 2,5 m/s2
3'600 min
< 2,5 m/s2
3'600 min
Verwendbare Werkzeuge
-1
10 Bürstenschleifkopf Typ BSK (inkl. 8+9 )
11 Faservliessbürsten-Räder
12 Filz-, Schwabbelscheiben mit Bohrung ø 14
Fiber-, Runddrahtbürsten mit Bohrung ø 14
Werkzeugwechsel
Spindel 1 mit Schlüssel 2 festhalten und die Überwurfmutter 3 mit
Schlüssel 2 lösen oder spannen.
Weiteres Zubehör
-1
Ist mit den dazugehörigen Bestellnummern in den
aufgeführt.
Änderungen vorbehalten.
Maintenance
• Store machine in a dry, clean place.
• Cooling air ports must be kept free of obstructions.
• Unplug before performing any maintenance work.
• Check connecting cables regularly. Damaged cables must be
replaced under all circumstances.
• Repairs may only be performed by a qualified electrician Acci-
dents could otherwise occur for the operator.
• Complaints can only be accepted if the machine is returned uno-
pened.
2.
Flexible shaft
Machine elements
B1 Threaded coupling DIN
B2 Threaded coupling DIN
B3 Spring-loaded pin
B4 Casing
Type NA12 DIN 10 / G28, permissible operating speed
Type NA12 DIN 15 / G35, permissible operating speed
Type NA15 DIN 15 / G35, permissible operating speed
Maintenance
• Store flexible shaft in a dry, clean place.
• If used daily: Re-grease once monthly. Remove core B5 from ca-
sing B4. Remove shaft grease. Lightly apply
to core B5. Order No. for 1 kg can: 904 832.
1
• New shafts or newly greased shafts require running-in.
• Clean casing coupler B2 B8 before use. Worn casing couplers
lead to increased vibration and noise. The casing B4 must then
be replaced (see spare parts list).
-1
3.1. Operating speed
-1
Ensure that the desired speed is permissible for the tool used.
3.2 Connect the flexible shaft
1. Insert pin in retention hole.
2. Slightly withdraw threaded coupling B1 from casing coupler B2.
3. Insert second pin through transverse hole in threaded coupling
B1 and
-1
4. fasten tightly onto the motor shaft A2.
-1
5. Remove pins.
-1
6. Insert casing coupler B2 completely into hole.
-1
7. Depress spring-loaded pin B3 and completely insert casing coup-
-1
ler B2.
-1
8. Spring-loaded pin B3 must click audibly into place in the retention
hole. Ensure that spring-loaded pin B3 has locked firmly into
place. If necessary, move / rotate casing coupler B2 until spring-
(Fig. B)
B5 Core
B6 Driving pin
B7 Spring-loaded pin
B8 Casing coupler G
(Fig. A)
to the motor (Figs. A +B)
- Katalogen
12'000 RPM
12'000 RPM
8'000 RPM
shaft grease
Werbung
