Additional Safety Instructions; Technical Data; Operation - Scheppach HG2000 Originalbetriebsanleitung

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords incre-
ase the risk of electric shock.
• If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
• Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must
be repaired.
General instructions for hot air blowers
• This appliance may be used by children aged 8 ye-
ars and above and by persons with limited physical,
sensory or mental capabilities or lack of experience
and knowledge, provided that they are under su-
pervision or have been told how to use the appli-
ance safely and are aware of the potential risks.
Children must not use the appliance as a plaything.
Cleaning and user maintenance tasks may not be
carried out by children unless they are supervised.
• To avoid potential risks, if the appliance power cord
is damaged it must be replaced by the manufactu-
rer, its customer service or by a qualified technici-
an.
• Have your power tool serviced by a qualified repair
person using only original replacement parts. This
will ensure that the safety of the power tool is main-
tained.
• Plugs and power cords should only be repla-
ced by the manufacturer of the power tool or the
manufacturer's authorised customer service agent.
This will ensure that the safety of the power tool is
maintained.
Safety instructions for the hot air blower
• Careless use of the appliance can cause a fire.
• Take care when using the appliance in the vicinity
of inflammable materials.
• Do not aim at the same place for a prolonged pe-
riod of time.
• Do not use in the presence of an explosive atmos-
phere.
• Heat can be transferred to combustible materials
which are hidden from view.
• Do not leave the appliance unattended while it is
in operation.
• Supervise children to ensure that they do not play
with the hot air blower.

Additional safety instructions

CAUTION! Avoid the risk of injury or fire as well
as health risks:
• In case of danger, remove the power plug from the
socket immediately.
• CAUTION! RISK OF INJURY! Never use the appli-
ance as a hair dryer.
• Never aim the hot air stream at people or animals.
• Never look directly into the nozzle on the outlet .
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
• CAUTION! RISK OF BURNS! Do not touch the hot
nozzle. Wear protective gloves.
• CAUTION! RISK OF FIRE AND EXPLOSION! The
appliance generates a lot of heat. Careless use can
lead to an increased risk of fire and explosions.
• Do not work in the presence of flammable gases
or materials, or in an explosive environment. When
working on plastics, paints, lacquers, etc., hazar-
dous gasses can be released. Always ensure suf-
ficient ventilation.
• Always remove the plug from the power socket
during work breaks, when adjusting the appliance
(e.g. changing nozzles) and when it is no longer in
use.
• Keep the nozzle at a distance from the workpiece
or the area being processed. A build-up of hot air
can result in damage to the appliance.
• Pay close attention to the area being worked and
also the surrounding area. The heat can reach
combustible parts outside your field of vision.
• The appliance must always be kept clean, dry and
free from oil or grease.
• Never use the appliance for purposes other than
the ones for which it was designed.

Technical Data

Rated voltage:
Nominal power:
Air flow:
Temperature (nozzle
outlet):
Protection class:

Operation

m Caution!
Do not cover the ventilation slots.
m Caution! Risk of burns!
Do not touch the hot nozzle
Switching the appliance on (fig. 1):
• Move the two-stage ON/OFF switch (3) to position
"I" or "II".
Setting the temperature (fig. 1)
• Move the two-stage ON/OFF switch (3) to position
"0".
Temperatur einstellen (Fig. 1)
The temperature can only be adjusted on the display
(4) when the two-stage ON/OFF switch is in position
"II".
Position "I" = cold air stage
Is suitable for cooling an overheated workpiece or for
drying of paint.
220-240 V~ / 50/60 Hz
2000 W
250 L/min / 500 L/min
50°C
50°C - 650°C
II
GB І 13