Japanische Funkzulassung; Crn-Zulassung - Endress+Hauser Micropilot FMR51 Technische Information

Japanische Funkzulassung

CRN-Zulassung

8) Except of FMR50-######BM* (Horn 40mm/1-1/2", PVDF encapsulated)
9) Except for FMR51-######BA* (Horn 40mm/1-1/2") and FMR51-######BB* (Horn 50mm/2")
10) Except for FMR52-######BO* (Horn 50mm/2", flush mount)
96
[Any] changes or modifications not expressly approved by the party responsible for compliance could
void the user' s authority to operate the equipment.
In addition, the devices FMR50
LPR (Level probe radar) regulation also for free space applicactions according to the FCC Code of
Federal Regulations, CFR 47, Part 15, Sections 15.205, 15.207, 15.209, 15.256 for antenna sizes
bigger than 50 mm (2,0 in). For these applications the devices must be professionally installed in a
downward operating position. In addition, the devices are not allowed to be mounted in a zone of
4 km around RAS stations and within a radius of 40 km around RAS stations the maxium operation
height of devices is 15 m (49 ft) above ground.
Die Geräte entsprechen dem Japanese Radio Law, Article 6, Section 1(1)
Für einige Gerätevarianten gibt es eine CRN-Zulassung. Eine CRN-Zulassung liegt vor, wenn folgende
zwei Bedingungen erfüllt sind:
• Das Gerät hat eine CSA-Zulassung (Produkstruktur: Merkmal 010 "Zulassung")
• Das Gerät hat einen CRN-zugelassenen Prozessanschluss gemäß folgender Tabelle:
Merkmal 100 der Produkststruktur
AFJ
AFK
AFM
AGJ
AGK
AGM
AHJ
AHK
AHM
AJJ
AJK
AJM
ARJ
ARM
ASJ
ASM
ATJ
ATK
ATM
MRK
MTK
RGJ
RVJ
TDJ
TDK
TFJ
8) 9) 10)
, FMR51 , FMR52 , FMR56 and FMR57 are compliant with the
Prozessanschluss
NPS 2" Cl.150 RF, 316/316L
NPS 2" Cl.150, PTFE >316/316L
NPS 2" Cl.150, AlloyC >316/316L
NPS 3" Cl.150 RF, 316/316L
NPS 3" Cl.150, PTFE >316/316L
NPS 3" Cl.150, AlloyC >316/316L
NPS 4" Cl.150 RF, 316/316L
NPS 4" Cl.150, PTFE >316/316L
NPS 4" Cl.150, AlloyC >316/316L
NPS 6" Cl.150 RF, 316/316L
NPS 6" Cl.150, PTFE >316/316L
NPS 6" Cl.150, AlloyC >316/316L
NPS 2" Cl.300 RF, 316/316L
NPS 2" Cl.300, AlloyC >316/316L
NPS 3" Cl.300 RF, 316/316L
NPS 3" Cl.300, AlloyC >316/316L
NPS 4" Cl.300 RF, 316/316L
NPS 4" Cl.300, PTFE>316/316L
NPS 4" Cl.300, AlloyC >316/316L
DIN11851 DN50 PN25 Nutmutter, PTFE>316L
DIN11851 DN80 PN25 Nutmutter, PTFE>316L
Gewinde ANSI MNPT1-1/2, 316L
Gewinde EN10226 R1-1/2, 316L
Tri-Clamp ISO2852 DN51 (2"), 316L
Tri-Clamp ISO2852 DN51 (2"), PTFE>316L, 3A, EHEDG
Tri-Clamp ISO2852 DN70-76.1 (3"), 316L
Micropilot FMR51, FMR52
Endress+Hauser