Using The Appliance - BERTO’S G6F2B Bedienungshandbuch

fitting which fixes the cock to the pipe and replace the piece.
Thermocouple (gas rings)
Loosen the nuts fixing the thermocouple to the valve and
the burner and replace the piece.
Thermostat valve tap on the gas oven (Fig. 3)
Loosen the nuts of the gas ducts and of the thermocouple,
remove the thermostat bulb from the supporting clips
located inside the oven chamber and replace with the
new cock.
Oven thermocouple
Remove the floor, unscrew the nut on the tap and the
burner and replace the thermocouple.
Replacing the heating elements of electric ovens
Disconnect the switch upstream of the appliance so that
the unit will be disconnected from the mains. In the FE
oven, the lower heating elements are positioned under the
bottom and the upper heating elements are positioned on
the upper side of the cooking chamber. In the FE1 oven,
the heating element is positioned behind the conveyor on
the rear of the cooking chamber. To remove the heating
elements, loosen the screws fixing them; pay attention
to the connection leads. Use a screwdriver to disconnect
the connection leads and mount a new heating element
following the sequence in reverse.

USING THE APPLIANCE

START-UP
Warning:
- This appliance cannot be used by people (including
children) with impaired skills or without experience
and knowledge unless under the supervision of a
person responsible for their safety who provides
precise instructions about the use of the unit. Children
must be supervised to make sure that they don't play
with the unit. Only for professional use.
- Do not open the oven door if the cooking chamber is
hot.
- Use pots suitable to the diameter and power of the
burner.
Turning on and off the LIGHT POWER burner without
pilot flame (Fig. 2)
Turn the knob to the maximum position. Use a match or
other suitable means to turn on the burner.
For the version with ignition, press and rotate the knob
and keep it pressed until it ignites automatically without
using other flames.
Keep the knob pressed until the thermocouple heats up
and is capable of keeping the flame alive.
To turn the burner off, turn the knob to the right.
The flame can be adjusted:
to the main flow (big flame)
to the shortest flow (small flame)
Turning on and off the burner with pilot flame (Fig.
8-9)
Turn the knob to position and light the pilot burner by
using a match or other suitable means.
Keep the knob pressed till the thermocouple is heated and
the pilot flame is lit.
Turn the knob to the maximum and minimum position in
order to light the main burner of the corresponding ring.
To turn off the burner, turn the knob to the right until the
position. To turn off the pilot flame, turn the knob to
the "O" position.
Turning on and off the gas oven without pilot flame
(FG1 Oven) (Fig. 3)
Turn-on: Open the oven door, press and turn the knob
and, while keeping it pressed, use a flame to turn on the
oven at position M or use the piezo ignitor.
Keep the knob pressed down for about 20" after ignition,
so that the safety device activates. Now adjust the
thermostat setting to the one most suitable for the
chosen cooking method.
Turn-on and turn-off of gas oven with pilot flame (FG
Oven and Tuttoforno T - Fig. 5)
Turn on: open the oven door, press and turn the knob to
position
and keep it pressed while lighting the pilot
light with the piezoelectric lighter or a match.
This operation may be observed through the hole in the
oven floor. Keep the knob pressed down for about 20"
after ignition, so that the safety device activates.
Then adjust the thermostatic setting according to the
cooking programme required.
OPERATING INSTRUCTIONS
FOR ELECTRIC OVENS
TURNING ON AND OFF THE FE TYPE ELECTRIC OVEN
(Fig. 6)
By turning the selector switch (23) to the left or the right,
you can choose the type of cooking, heat above and/or
below. In either of these positions the green light comes
on (25 = live appliance).
By turning the selector switch (24) on desired position,
resistances are switched on, the warning light (26) comes
on and goes off when the selected temperature is reached
and the resistances switch off.
To turn the oven off, turn the thermostat into position ( )
and the selector into position (O).
TURNING ON AND OFF THE FE1 AND FE2 TYPE
ELECTRIC OVEN (Fig. 7)
In this type of oven the heat comes from the rear of
the chamber; it is, however, equipped with a fan which
distributes the heat evenly throughout the oven chamber.
By turning the selector switch (24) on desired position,
resistances are switched on, the warning light (26) comes
on and goes off when the selected temperature is reached
and the resistances switch off.
To turn off the oven, turn the thermostat to the off
position (O).
The first position of the knob corresponds to the fan
| 107
EN