Installation; Safety; Shower Operation; Appliance Description - AEG DDLE Basis 11 Bedienung Und Installation

INSTALLATION

7. Safety

Only a qualified contractor should carry out installation,
commissioning, maintenance and repair of the appliance.
7.1 General safety instructions
We guarantee trouble-free function and operational relia-
bility only if original accessories and spare parts intended
for the appliance are used.
Material losses
!
Observe the maximum inlet temperature. Higher
temperatures may damage the appliance. You can
restrict the maximum inlet temperature by installing
a central thermostatic valve.
WARNING Electrocution
This appliance contains capacitors which are dis-
charged when disconnected from the power supply.
The capacitor discharge voltage may briefly reach
> 60 V DC.
7.2

Shower operation

CAUTION Burns
» If supplying a shower, set the internal temper-
ature limit to "Tred"; see chapter "Installation
alternatives / Temperature limit".
CAUTION Burns
If the water supplied to the appliance is preheated,
please note the following:
The internally adjustable temperature limit may be
exceeded.
» Limit the temperature with an upstream central
thermostatic valve.
7.3 Instructions, standards and regulations
Note
Observe all applicable national and regional regula-
tions and instructions.
◦ The IP 25 (hoseproof) rating can only be ensured
with a correctly fitted cable grommet.
◦ The specific electrical resistivity of the water must
not fall below that stated on the type plate. In a linked
water network, factor in the lowest electrical resist-
ance of the water (see chapter "Installation / Spec-
ification / Data table"). Your water supply utility will
advise you of the specific electrical water resistivity
or conductivity.

8. Appliance description

8.1

Standard delivery

The following are delivered with the appliance:
◦ Wall mounting bracket
◦ Threaded studs, screws and rawl plugs for the wall
mounting bracket
◦ Installation template
◦ 2 twin connectors (cold water with shut-off valve)
◦ Flat gaskets
◦ Cable grommet (power cable from above / below)
◦ Screws / rawl plugs for securing the back panel to
allow for water connection on finished walls
◦ Additional flow limiter in the cold water pipe (only
DDLE Basis 18/21/24)

8.2 Accessories

Tap
ADEo 70 WD Mono lever mixer tap with bath / shower
changeover
Stove connection set
Connection set for the power connection of the
DDLE Basis 11 and DDLE Basis 13
Installation accessories
Pipe assembly, undersink installation UT 104, connec-
tions: Finished walls, G 3/8, top. Water connections with
12 mm compression fitting.
Universal mounting frame
Mounting frame with electrical connections.
Pipe assembly for undersink appliances
This assembly for undersink installation is required if you
need to have the water connections (G ⅜ A) above the
appliance.
Pipe assembly for offset installation
You will need the pipe assembly with bends if you intend
to offset the appliance by 90 mm downwards from the
water connection.
Pipe assembly for replacing a gas water heater
You will need the pipe assembly if you are using the exist-
ing gas water heater connections (cold water connection
on the left-hand side DHW connection on the right-hand
side).
Load shedding relay (LR 1-A)
The load shedding relay for installation in the distribution
board provides priority control for the instantaneous water
heater when other appliances, such as electric storage
heaters, are being operated simultaneously.
Central thermostatic valve
Use the thermostatic valve for central premixing when
operating an instantaneous water heater with preheated
water, for example. For use in shower operation, the valve
must be set to a maximum of 55 °C.

9. Preparation

9.1

Installation location

Material losses
!
Install the appliance in a room free from the risk of
frost.
» Always install the appliance vertically and near the
draw-off point.
The appliance is suitable for undersink and oversink in-
stallation.
Installation
21