HIKOKI CJ 36DA Bedienungsanleitung Seite 12

English
18. Chip cover
○ Chip cover prevents chips from fl ying off and improves
the effi ciency of dust collector.
○ There is a possibility that chip cover is frosted when
cutting the metal.
19. In order to prevent blade dislodging, damage or
excessive wear on the plunger, please make sure to
have surface of the base plate attached to the work piece
while sawing.
20. At low speed do not cut a wood with a thickness of more
than 10 mm or metal with a thickness of more than 1 mm.
21. To ensure accurate cutting when using the guide
(Fig. 16), always set the orbital position to "0".
22. When sawing a small circular arc, reduce the feeding
speed of the machine. If the machine is fed too fast, it
could cause the blade to break.
23. Circular cutting must be done with the blade
approximately vertical to the bottom surface of the base.
24. Angular cutting can not be done when adopting dust
collector.
25. Connecting with cleaner (sold separately)
By connecting with cleaner through dust collector and
adapter (sold separately), most of dust can be collected.
26. When cutting metallic materials, use an appropriate
cutting fl uid (spindle oil, soapy water, etc.) to prolong
the bladeʼs service life. (Fig. 17) And cut the material at
medium speed.
27. When cutting a window hole in materials other than
lumber, initially bore a hole with a drill or similar tool from
which to start cutting. (Fig. 18)
28. Do not fi x and secure the switch lock. Besides, keep
your fi nger off the switch trigger when the tool is being
carried around. Otherwise, the main body switch can
be inadvertently turned ON, resulting in unexpected
accidents.
29. Do not expose directly your eye to the light by looking
into the light.
If your eye is continuously exposed to the light, your eye
will be hurt.
30. Never touch moving parts.
Never place your hands, fi ngers or other body parts near
the tool's moving parts.
31. Never operate without all guards in place.
Never operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard or
safety feature before resuming operation of the tool.
32. NEVER leave tool running unattended. Turn power off .
Don't leave tool until it comes to a complete stop.
33. Do not operate power tools in explosive atmospheres,
such as in the presence of fl ammable liquids, gases or
dust.
Jig saw create sparks which may ignite the dust or
fumes.
34. The power tool is equipped with a temperature
protection circuit to protect the motor. Continuous work
may cause the temperature of the unit to rise, activating
the temperature protection circuit and automatically
stopping operation. If this happens, allow the power tool
to cool before resuming use.
35. Do not give a strong shock to the switch panel or break it.
It may lead to a trouble. (CJ36DB only)
36. Do not use the product if the tool or the battery terminals
(battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
37. Keep the tool's terminals (battery mount) free of swarf
and dust.
○ Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○ During use, try to avoid swarf or dust on the tool from
falling on the battery.
○ When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result in
smoke emission or ignition.
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with the
protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such a case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes of
overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and caution.
WARNING
In order to prevent any battery leakage, heat generation,
smoke emission, explosion and ignition beforehand, please
be sure to heed the following precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○ During work make sure that swarf and dust do not fall on
the battery.
○ Make sure that any swarf and dust falling on the power
tool during work do not collect on the battery.
○ Do not store an unused battery in a location exposed to
swarf and dust.
○ Before storing a battery, remove any swarf and dust that
may adhere to it and do not store it together with metal
parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject the
battery to severe physical shock.
3. Do not use an apparently damaged or deformed battery.
4. Do not use the battery in reverse polarity.
5. Do not connect directly to an electrical outlets or car
cigarette lighter sockets.
6. Do not use the battery for a purpose other than those
specifi ed.
7. If the battery charging fails to complete even when a
specifi ed recharging time has elapsed, immediately stop
further recharging.
8. Do not put or subject the battery to high temperatures or
high pressure such as into a microwave oven, dryer, or
high pressure container.
9. Keep away from fi re immediately when leakage or foul
odor are detected.
10. Do not use in a location where strong static electricity
generates.
11. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears abnormal
during use, recharging or storage, immediately remove it
from the equipment or battery charger, and stop use.
12