Technical Data; Installation - DITEC CUBIC6 Montage- Und Wartungshandbuch

1.

TECHNICAL DATA

GB
Power supply
Absorption
Torque
Condenser
Opening time
Service class
Intermittence
Temperature
Degree of protection
Control panel
Applications
m = leaf width
kg = leaf weight
CUBIC6L*
CUBIC6LG**
CUBIC6TIG**
CUBIC6TC
2. REFERENCE TO ILLUSTRATIONS
The given operating and performance features can only be guar-
anteed with the use of DITEC accessories and safety devices.
2.1 Standard installation references (fig. 1)
[1] Radio
[2] Flashing light
[3] Key selector
[4] Connect power supply to an type-approved omnipole
switch with a contact opening gap of no less that 3 mm
(not supplied)
[5] Control panel
[6] Geared motor
[7] Photocells
2.2 Accessories
CUBIC6C Foundation casing
CUBIC6CG Oversize foundation casing
CUBIC6CY Stainless steel foundation casing
CUBIC6L Lever mechanism kit
CUBIC6LG Oversize lever mechanism kit
CUBIC6TC Chain-operated lever mechanism kit
CUBIC6TIG Oversize gear-operated lever mechanism kit
CUBIC6SBL Lever-operated release kit
CUBIC6SBD Key-operated release kit
CUBIC6FM Magnetic limit switch kit
CUBIC6FMTI Magnetic limit switch kit for lever mechanism
3.

INSTALLATION

Unless otherwise specified, all measurements are expressed
in millimetres (mm).
CUBIC6 - IP1812
CUBIC6 CUBIC6J
230 V~ / 50 Hz 120 V~ / 60 Hz
1,5 A
340 Nm 340 Nm
10 µF
18 s / 90° 18 s / 90°
3 - FREQUENT 3 - FREQUENT
S2 = 15min S2 = 15min
S3 = 25% S3 = 25%
-20° C / +55° C -20° C / +55° C
IP67
E2
600 kg
500 kg
400 kg
300 kg
200 kg
100 kg
1 2 3 4 5
[CUBIC6C*]
CUBIC6H
24 V=
4 A 12 A
340 Nm
40 µF -
12÷25 s / 90°
4 - INTENSIVE
S2 = 30min
S3 = 50%
-20° C / +55° C
IP67 IP67
E2 J VIVAH
800 kg
700 kg
600 kg
500 kg
400 kg
300 kg
200 kg
100 kg
1 2 3 4
m
[CUBIC6CG**]
3.1 Preliminary checks
Check that the structure is sufficiently sturdy and that the hinge
pivots are properly lubricated. Provide an opening and closing
stop.
Note: if the gate wing is more than 2.5 m wide, an electric lock
should be installed.
3.2 Foundation case installation
Install the foundation case as indicated in the relevant manual.
3.3 Lever mechanisms installation
Choose and install the lever mechanisms as indicated in the
relevant manual.
3.4 Wing release installation
Choose and install the door release mechanisms as indicated
in the relevant manual.
Attention: to install the releases more easily, we advise you to
position the gate at the centre of the foundation casing and re-
move the lid, in such a way as to have enough space for fixing
the screws.
10
CUBIC6V
230 V~ / 50 Hz
1,5 A
220 Nm
10 µF
9 s / 90°
3 - FREQUENT
S2 = 15min
S3 = 25%
-20° C / +55° C
IP67
E2
600 kg
500 kg
400 kg
300 kg
200 kg
100 kg
5 m
1 2
CUBIC6HV
24 V=
12 A
220 Nm
-
6÷13 s / 90°
4 - INTENSIVE
S2 = 30min
S3 = 50%
-20° C / +55° C
IP67
VIVAH
3 4 5 m