Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
I Attach the bracket to the wall as shown in detail 1 of
I Using the compensator holes as reference, drill holes in the wall
and insert the plastic plugs (
pensator to the wall as shown (detail 3).
I Using the other series of holes on the compensator as refer-
ence, drill holes in the panel and attach with the screws and bolts
shown (detail 5).
Before drilling the holes, check again that the panel is
straight in the area of the groove in which the sliding
glass panel will rest (detail 4).
I Click the covering profile into position (
insert the end cover cap.
I Remove the double sided adhesive tape and, according to the
model provided, glue the "L"-shaped cover to the glass panel as
shown (detail 2), to fill the "remaining" gap between the wall.
Installation of the outer closure panel
(An optional item for installation in the centre of the room,
available for J•Twin Premium and Amea Twin Premium)
The operations described should be carried out at the
same time as those shown in
The closure panel (and related compensator for attach-
ment to the wall) are supplied in a separate packaging.
I Line up the compensator on the tub along the previously pre-
i
pared mark on the wall (
i
given in
20, detail 1a, to identify the position of the holes.
I Drill the holes in the wall, insert the plastic plugs and attach the
compensator as shown in detail 2.
I Apply some "spots" of silicone to the groove of the glass panel
i
upright (
21, detail 1), then insert the panel; then insert it into
the compensator groove (detail 2).
I Using the compensator holes as reference, drill the holes in the
panel and attach it with the screws and bolts shown in detail 2;
then place the white caps onto the screw heads.
By installing the outer closure panel, the "L"-shaped cover
i
(
19, detail 12) will not be used.
Installation of the sliding glass panel
I Assemble the sliding glass panel (
sliding block into the lower sliding profile (detail 1); then insert the
rollers into the upper profile, push them downwards and then
tighten them using the screws (detail 2).
I Apply silicone to the holes as shown in detail 3 and, according
to the model, attach the relevant slide-support of the sliding glass
panel to the tub.
I Check that the glass panel is straight and slides well; if you
need to adjust the rollers, in order to guarantee alignment and
easy sliding, loosen the screw that fixes the cam, rotate it as
required and then tighten the screw (detail 2).
i
18, detail 2); then attach the com-
i
19, detail 1) and
i
17-18.
8). In any case, refer to the indications
i
22) by first inserting the
i
Finishing touches
18.
I Attach the tub to the floor following the instructions shown in
i
23, detail 1.
I If the tub is provided with a hydromassage system, connect the
electric wiring box to the electric mains and the earth system,
according to the wiring diagram and the instructions given in the
"Electric connections and safety" chapter.
I If provided, insert the knobs into the air adjustment pins as far as
they will go (detail.2). There is a compulsory position for the insertion
of the knob in relation to the adjustment pin: if they are not matched
up and the knob is forced the pin may break.
I If provided, click the flange cover into position on the hydromas-
sage jets (detail 3) and attach the suction inlet cover, which is pro-
vided with an O-ring (detail 4).
I For models equipped with disinfection system, remove the bot-
tle containing the liquuid disinfectant from the tub support and
pour it into the opening hidden by the plate flap.
I If provided, try out the hydromassage and all the shower area
functions, making sure that they are watertight, especially around
the hydraulic connections and the drain.
I Carefully apply silicone along the edges at points that will rest against
the wall (detail 5); it is advisable to install Jacuzzi
(detail 6) that guarantee an excellent finishing touch.
Tub panels installation
I Attach the under-edge springs (a) to the plugs (b) that are
under the tub rim (
The number of under-edge springs depends on the chosen
model.
I Click the corner springs into position (c) on the legs and posi-
tion them so they touch the top inside the rim; then insert the lock
rings (d) into the grooves of the legs (detail 2).
The J•Sha ActiveTwin model has 2 types of spring: one
with arms of the same length (symmetrical type, c) and
one with arms of different lengths (asymmetrical type,
c1); therefore to assemble the front panel asymmetrical-
type springs must be used, making sure that the longest
arm is positioned along the front of the tub (
J•Twin and Amea Twin Premium
I Insert the plastic supports (e) onto the legs by pressing and
adjust the height according to the dimension shown (
ing sure that you position them at 90° in relation to the tub rim;
then fix the supports using the nuts, without tightening them too
much.
I Attach the plastic clips (f) onto the side panel; use the holes
(3-4) or the holes (1-2) according to whether you want to
attach the panel to the right or the left (
I Insert the side panel between the corner springs (c) and the tub
rim, and lift it up until the clips (f) are lined up with the supports
8
i
24, detail 1).
i
26).
®
trimming profiles
i
24).
i
25), mak-
Werbung
Inhaltsverzeichnis
