Prior To Operation - DeWalt DWE46105 Bersetzt Von Den Originalanweisungen

EngLIsh
Corner Door Application (Fig. F)

WARNING: To reduce the risk of injury, ALWAYS turn
the tool off and disconnect the tool from the power
source before making any adjustments or removing
or installing attachments or accessories. This applies
to both the grinder and the dust extractor vacuum.
Such preventative safety measures reduce the risk of
starting the tool accidentally.

WARNING: Risk of personal injury. The corner door should
only be opened for cutting inside corners. Keep hands and
body away from cutting area at all times. Ensure corner
door is closed in all other applications.
This feature allows the cutting of an inside corner.
1. Ensure the tool is off and wheel has come to a
complete stop.
2. Turn cornering door locking lever
full rotation. Grasp the corner door
3. Place hands away from the wheel area and position
yourself so the open underside of the shroud is facing away
from you.
4. Turn the tool on and allow the tool to reach full speed
before touching the tool to the work surface.
5. Place the wheel onto the work surface and move the
grinder from right to left to cut around the inside corner for
best dust collection.
6. Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
7. Close the corner door and lock in place using the cornering
door locking lever .
12
Dust Extraction (Fig. G)

WARNING: Use only power tools recommended by
D WALT with this attachment.
e
For more information about D
e
with this attachment, please contact one of our authorisec
services centers, listed on the back cover, or refer to the full
details of our after-sales service available on the Internet at:
www.2helpU.com.

WARNING: This attachment must be used with a dust
extractor system. ALWAYS wear certified safety face or
dust mask.
nOTE: Ensure hose connection is secure.
nOTE: The amount of dust retained by the dust extractor
vacuum is dependent on its filter system. Refer to the dust
extractor vacuum instruction manual for more information.
All D WALT dust collection shrouds are designed to work with
e
the D WALT Airlock DWV9000 connector.
e
1. Attach the DWV9000 connector
hose 20 .
2. Unlock the DWV9000 connector
port 8 .
3. Lock the DWV9000 connector
30
12 counterclockwise one
13 and rotate open.
WALT power tools compatible
19 to your dust collector
and slide onto dust
19
19 to secure.
Traditional dust extractor vacuum hoses
(Fig. G)
Attach recommended dust extractor vacuum hose to dust port

Prior to Operation

• Install the guard and appropriate disc or wheel. Do not use
excessively worn discs or wheels.
• Be sure the inner and outer flanges are mounted correctly.
• Make sure the disc or wheel rotates in the direction of the
arrows on the accessory and the tool.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the side handle
with the other hand on the body of the tool, as shown in
figure H.
Slider Switch (Fig. A)

WARNING: Before using the tool, check that the side
handle is tightened securely.

CAUTION: Before connecting the tool to a power supply,
be sure the switch is in the off position by pressing the rear
part of the switch and releasing. Ensure the switch is in
the off position as described above after any interruption
in power supply to the tool, such as the activation of a
ground fault interrupter, throwing of a circuit breaker,
accidental unplugging, or power failure. If the switch
is locked on when the power is connected, the tool will
start unexpectedly.
To start the tool, slide the ON/OFF slider switch
front of the tool. To stop the tool, release the ON/OFF switch.
For continuous operation, slide the switch toward the front of
the tool and press the forward part of the switch inward. To stop
the tool while operating in continuous mode, press the rear part
of the switch and release.
8 .
3 ,
toward the
7