DeWalt DWE46105 Bersetzt Von Den Originalanweisungen Seite 33

Spindle Lock (Fig. A)
The spindle lock button is provided to prevent the spindle
1
from rotating when installing or removing wheels. Operate the
spindle lock only when the tool is turned off, unplugged from
the power supply, and has come to a complete stop.
NOTICE: To reduce the risk of damage to the tool, do
not engage the spindle lock while the tool is operating.
Damage to the tool will result and attached accessory
may spin off possibly resulting in injury.
To engage the lock, depress the spindle lock button
and rotate the spindle until you are unable to rotate the
spindle further.
Mortar Raking Shroud Operation

WARNING: To reduce the risk of injury, ALWAYS turn
the tool off and disconnect the tool from the power
source before making any adjustments or removing
or installing attachments or accessories. This applies
to both the grinder and the dust extractor vacuum.
Such preventative safety measures reduce the risk of
starting the tool accidentally.

WARNING: For your own safety, read the instruction
manual for both the grinding tool and the dust extractor
vacuum before using any accessory. Failure to heed
these warnings may result in personal injury and serious
damage to the tool and the accessory. When servicing this
tool, use only identical replacement parts.

WARNING: Hold the side handle and body of the tool
firmly to maintain control of the tool at start up and
during use and until the wheel or accessory stops rotating.
Make sure the wheel has come to a complete stop be fore
laying the tool down.

WARNING: Ensure corner door is closed.
1. Ensure all assembly and adjustment instructions have
been completed.
2. Turn the dust extractor vacuum on as instructed in the dust
extractor vacuum instruction manual.
3. Start grinder as instructed in tool instruction manual.
nOTE: Allow the tool to reach full speed before applying to
the work surface.
Tuckpointing and Cutting Application
(Fig. H)
1. Set the desired depth of cut, see Depth of Cut Adjustment
under assembly and adjustments.
2. Allow the tool to reach full speed before touching the tool
to the work surface.
3. Position yourself so the open underside of the shroud and
the wheel are facing away from you.
4. Place the edge 22 of shroud onto the work surface and
begin cut by plunging into the work surface. nOTE: Keep
the edge 22 of the shroud against the work surface to
ensure proper dust collection.
5. With the shroud oriented as shown in figure H, move the
grinder right to left along the work surface. For the best
results the grinder should be positioned at a 45° angle to
the dust port when tuckpointing/cutting.
6. Remove the tool from work surface before turning tool off.
Allow the tool to stop rotating before laying it down.
MAINTENANCE
Your D WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
1
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
Lubrication
Your power tool requires no additional lubrication.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
Optional Accessories

WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
e
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
Consult your dealer for further information on the
appropriate accessories.
Protecting the Environment
Separate collection. Products and batteries marked
with this symbol must not be disposed of with normal
household waste.
Products and batteries contain materials that can
be recovered or recycled reducing the demand for raw
materials. Please recycle electrical products and batteries
according to local provisions. Further information is available at
www.2helpU.com.
EngLIsh
WALT recommended
e
31