Parts Description - Makita LS1019 Betriebsanleitung

15. Make sure the shaft lock is released before the
switch is turned on.
16. Be sure that the blade does not contact the
turn base in the lowest position.
17. Hold the handle firmly. Be aware that the saw
moves up or down slightly during start-up and
stopping.
18. Make sure the blade is not contacting the
workpiece before the switch is turned on.
19. Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
20. Stop operation immediately if you notice any-
thing abnormal.
21. Do not attempt to lock the trigger in the "ON"
position.

PARTS DESCRIPTION

► Fig.2
1 Slide pole
5 Holder
9 Kerf board
13 Blade guard
17 Adjusting bolt (for maxi-
mum cutting capacity)
21 Grip (for turn base)
► Fig.3
1 Switch trigger
5 Hose (for dust
extraction)
9 Dust bag
13 Latch lever (for bevel
angle)
INSTALLATION
Installing the grip
Screw the threaded shaft of the grip into the turn base.
► Fig.4: 1. Grip 2. Turn base
Installing the dust extraction hose
Connect the dust extraction hose to the tool as
illustrated.
Make sure that the elbow and the sleeve fit properly to
the ports of the tool.
► Fig.5: 1. Dust extraction hose 2. Elbow 3. Sleeve
4. Port
2 Stopper pin (for carriage
sliding)
6 Turn base
10 Blade case
14 Knob (for bevel angle)
18 Stopper arm
- -
2 Lock-off button
6 Stopper pin (for carriage
elevation)
10 0° adjusting bolt (for
bevel angle)
14 Pointer (for bevel angle)
22. Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive wheels may cause an injury.
23. Some material contains chemicals which may be
toxic. Take caution to prevent dust inhalation and
skin contact. Follow material supplier safety data.
Additional safety rules for the laser
1. LASER RADIATION, DO NOT STARE INTO THE
BEAM OR VIEW DIRECTLY WITH OPTICAL
INSTRUMENTS, CLASS 2M LASER PRODUCT.
SAVE THESE INSTRUCTIONS.
WARNING:
product (gained from repeated use) replace strict adher-
ence to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.
3 Vertical vise
7 Pointer (for miter angle)
11 Adjusting screw (for
laser line)
15 Hex wrench
19 Lock lever (for turn base)
- -
3 Hole for padlock
7 Guide fence (lower
fence)
11 Bevel angle scale
15 45° adjusting bolt (for
bevel angle)
Bench mounting
When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. While lowering the
handle slightly, pull the stopper pin and rotate it 90°.
► Fig.6: 1. Locked position 2. Unlocked position
3. Stopper pin
This tool should be bolted with four bolts to a level and
stable surface using the bolt holes provided in the tool's
base. This will help prevent tipping and possible injury.
► Fig.7: 1. Bolt
WARNING:
on the supporting surface. Movement of the miter
saw on the supporting surface while cutting may
result in loss of control and serious personal injury.
17 ENGLISH
DO NOT let comfort or familiarity with
4 Releasing button (for
right side bevel angle)
8 Miter angle scale
12 Range adjustment screw
(for laser line)
16 Adjusting screw (for
lower limit position)
20 Releasing lever (for turn
base)
-
4 Switch (for laser line)
8 Guide fence (upper
fence)
12 Releasing lever (for 48°
bevel angle)
-
Ensure that the tool will not move
-
-