Parts Description - Makita LS002G Betriebsanleitung

Important safety instructions for
wireless unit
1. Do not disassemble or tamper with the wireless unit.
2. Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
3. Use the wireless unit only with Makita tools.
Do not expose the wireless unit to rain or wet
4.
conditions.
5. Do not use the wireless unit in places where
the temperature exceeds 50°C (122°F).
6. Do not operate the wireless unit in places
where medical instruments, such as heart
pace makers are nearby.
7. Do not operate the wireless unit in places where
automated devices are nearby. If operated, auto-
mated devices may develop malfunction or error.
8. Do not operate the wireless unit in places under
high temperature or places where static elec-
tricity or electrical noise could be generated.
9. The wireless unit can produce electromagnetic
fields (EMF) but they are not harmful to the user.
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct direction.

PARTS DESCRIPTION

► Fig.2
1 Hex wrench
5 Wireless activation
button
9 Blade guard
13 Releasing lever (for turn
base)
17 Miter angle scale
21 Releasing lever (for right
side bevel angle)
25 Right bevel angle scale
29 Lid (for wireless unit)
► Fig.3
1 Hole for padlock
5 Battery cartridge
9 Releasing lever (for 48°
bevel angle)
2 Adjusting bolt (for maxi-
mum cutting capacity)
6 Wireless activation lamp
10 Kerf board
14 Adjusting bolt (for turn
base)
18 Turn base
22 45° adjusting bolt (for
right bevel angle)
26 Pointer (for right bevel
angle)
- -
2 Switch trigger
6 Dust extraction hose
10 45° adjusting bolt (for left
bevel angle)
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doing so may cause a malfunction of the wireless unit.
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place subject
to high heat, such as a car sitting in the sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
28. Do not pull and/or twist the lid of the slot more than
necessary. Restore the lid if it comes off from the tool.
29. Replace the lid of the slot if it is lost or damaged.
SAVE THESE INSTRUCTIONS.
3 Adjusting screw (for
lower limit position)
7 Vacuum button
11 Grip (for turn base)
15 Guide fences
19 Sub base
23 0° adjusting bolt (for
bevel angle)
27 Stopper pin (for carriage
sliding)
- -
3 Lock-off button
7 Left bevel angle scale
11 Shaft lock
19 ENGLISH
4 Stopper arm
8 Lamp button
12 Grip dial (for bevel
angle)
16 Pointer (for miter angle)
20 Vertical vise
24 Dust guide
28 Slide pole
- -
4 Carry handle
8 Pointer (for left bevel angle)
12 Dust bag (when replaced
with dust extraction
hose)