Parts Description - Makita LS002G Betriebsanleitung

Important safety instructions for
wireless unit
1. Do not disassemble or tamper with the wire-
less unit.
2. Keep the wireless unit away from young chil-
dren. If accidentally swallowed, seek medical
attention immediately.
3. Use the wireless unit only with Makita tools.
4. Do not expose the wireless unit to rain or wet
conditions.
Do not use the wireless unit in places where
5.
the temperature exceeds 50°C (122°F).
6. Do not operate the wireless unit in places
where medical instruments, such as heart
pace makers are nearby.
7. Do not operate the wireless unit in places
where automated devices are nearby. If oper-
ated, automated devices may develop malfunction
or error.
Do not operate the wireless unit in places
8.
under high temperature or places where
static electricity or electrical noise could be
generated.
The wireless unit can produce electromagnetic
9.
fields (EMF) but they are not harmful to the
user.
10. The wireless unit is an accurate instrument. Be
careful not to drop or strike the wireless unit.
11. Avoid touching the terminal of the wireless
unit with bare hands or metallic materials.
12. Always remove the battery on the product
when installing the wireless unit into it.
13. When opening the lid of the slot, avoid the
place where dust and water may come into the
slot. Always keep the inlet of the slot clean.
14. Always insert the wireless unit in the correct
direction.

PARTS DESCRIPTION

► Fig.2
1 Hex wrench
5 Wireless activation
button
9 Blade guard
13 Releasing lever (for turn
base)
17 Miter angle scale
21 Releasing lever (for right
side bevel angle)
25 Right bevel angle scale
29 Lid (for wireless unit)
2 Adjusting bolt (for maxi-
mum cutting capacity)
6 Wireless activation lamp
10 Kerf board
14 Adjusting bolt (for turn
base)
18 Turn base
22 45° adjusting bolt (for
right bevel angle)
26 Pointer (for right bevel
angle)
- -
15. Do not press the wireless activation button
on the wireless unit too hard and/or press the
button with an object with a sharp edge.
16. Always close the lid of the slot when
operating.
17. Do not remove the wireless unit from the slot
while the power is being supplied to the tool.
Doing so may cause a malfunction of the wireless
unit.
18. Do not remove the sticker on the wireless unit.
19. Do not put any sticker on the wireless unit.
20. Do not leave the wireless unit in a place where
static electricity or electrical noise could be
generated.
21. Do not leave the wireless unit in a place sub-
ject to high heat, such as a car sitting in the
sun.
22. Do not leave the wireless unit in a dusty or
powdery place or in a place corrosive gas
could be generated.
23. Sudden change of the temperature may bedew
the wireless unit. Do not use the wireless unit
until the dew is completely dried.
24. When cleaning the wireless unit, gently wipe
with a dry soft cloth. Do not use benzine, thin-
ner, conductive grease or the like.
25. When storing the wireless unit, keep it in the
supplied case or a static-free container.
26. Do not insert any devices other than Makita
wireless unit into the slot on the tool.
27. Do not use the tool with the lid of the slot dam-
aged. Water, dust, and dirt come into the slot may
cause malfunction.
28. Do not pull and/or twist the lid of the slot more
than necessary. Restore the lid if it comes off
from the tool.
29. Replace the lid of the slot if it is lost or
damaged.
SAVE THESE INSTRUCTIONS.
3 Adjusting screw (for
lower limit position)
7 Vacuum button
11 Grip (for turn base)
15 Guide fences
19 Sub base
23 0° adjusting bolt (for
bevel angle)
27 Stopper pin (for carriage
sliding)
- -
19 ENGLISH
4 Stopper arm
8 Lamp button
12 Grip dial (for bevel
angle)
16 Pointer (for miter angle)
20 Vertical vise
24 Dust guide
28 Slide pole
- -