Cebora WF4-SS31 Bedienungsanleitung Seite 140

1 VEILIGHEIDSVOORSCHRIFTEN ................................................................................................................................................. 141
1.1 PLAATJE MET WAARSCHUWINGEN ................................................................................................................................ 141
2 ALGEMENE BESCHRIJVING ........................................................................................................................................................142
2.1 VERKLARING VAN DE TECHNISCHE GEGEVENS ........................................................................................................142
3 INSTALLATIE EN INBEDRIJFSTELLING ...................................................................................................................................143
3.1 OPHIJSEN ................................................................................................................................................................................143
3.2 MONTAGE ................................................................................................................................................................................143
3.3 EVENTUELE VERLENGINGEN AANSLUITEN ................................................................................................................143
3.4 DE LASTOORTS AANSLUITEN ............................................................................................................................................144
3.5 DE KOELGROEP MONTEREN (ART. 1683 - OP AANVRAAG GELEVERD) ..................................................................145
3.6 PLAATSING ..............................................................................................................................................................................145
3.6.1 HELLINGEN ..................................................................................................................................................................145
3.7 INBEDRIJFSTELLING ............................................................................................................................................................145
4 BESCHRIJVING VAN DE GENERATOR ......................................................................................................................................146
5 BESCHRIJVING VAN DE KOELGROEP .......................................................................................................................................147
5.1 AANSLUITINGEN ...................................................................................................................................................................148
5.2. BESCHRIJVING VAN DE BEVEILIGINGEN .......................................................................................................................148
5.2.1 BEVEILIGING DRUK KOELVLOEISTOF .................................................................................................................148
5.2.2 ZEKERING (T 2A/250V-Ø 5X20) ................................................................................................................................148
5.3 INBEDRIJFSTELLING ............................................................................................................................................................148
6 BESCHRIJVING VAN HET BEDIENINGSPANEEL ....................................................................................................................148
6.1 BEDIENINGSPANEEL ............................................................................................................................................................148
6.2 INSTELLINGENPANEEL .......................................................................................................................................................149
6.3 WEERGAVE ALARMEN ........................................................................................................................................................150
6.4 WEERGAVE STORINGEN ......................................................................................................................................................150
7 DE MACHINE PROGRAMMEREN "MAIN MENU" - "HOOFDMENU" .................................................................................150
7.1 MENU "PROCESS PARAMS" - "PROCESPARAMETERS" ...............................................................................................151
7.1.1 "PROCESS" - "PROCES" ..............................................................................................................................................151
7.1.2 "MATERIAL" - "MATERIAAL" .................................................................................................................................151
7.1.3 "DIAMETER" - "DIAMETER" ....................................................................................................................................151
7.1.4 "GAS" .............................................................................................................................................................................151
7.1.5 "ARC LENGTH CORR" - "CORRECTIE LENGTE BOOG" .....................................................................................151
7.1.6 "INDUCTANCE CORR" - "CORRECTIE IMPEDANTIE" .......................................................................................151
7.1.7 "START MODE" - "STARTWIJZE" ............................................................................................................................151
7.1.8 "SPOT" - "PUNTEN / INTERMITTEREND" .............................................................................................................152
7.1.9 "HSA" - "HOT START AUTOMATICO" .....................................................................................................................152
7.1.10 "CRA" - "EINDKRATER VULLEN" ..........................................................................................................................152
7.1.11 "SOFT START" - "BENADERING" ............................................................................................................................152
7.1.12 "BURNBACK" ...............................................................................................................................................................152
7.1.13 "DOUBLE LEVEL" - "DUBBEL NIVEAU" ................................................................................................................152
7.1.13.1 "FREQUENCY" - "FREQUENTIE" VAN HET DUBBELE NIVEAU .........................................................152
7.1.13.2 "PULSE STEP": DE BREEDTE VAN DE VARIATIE VAN DE SNELHEID IN M/MIN ...........................153
7.1.13.3 "DUTY CYCLE": TIJD VAN HET DUBBELE NIVEAU .............................................................................153
7.1.13.4 "ARC LENGTH COR" - "CORRECTE LENGTE BOOG ..............................................................................153
7.1.14 "DOUBLE PULSE" - "DUBBELE PULS" ....................................................................................................................153
7.1.15 "PREFLOW" - "PRE GAS" ...........................................................................................................................................153
7.1.16 "POSTFLOW" - "POST GAS" ......................................................................................................................................153
7.1.17 "SPEED CORR" - "CORRECTIE VAN DE SNELHEID" ..........................................................................................153
7.2 MENU "JOB" ............................................................................................................................................................................153
7.2.1 EEN PROGRAMMA "JOB" OPSLAAN ......................................................................................................................153
7.3 MENU "SETTINGS" - "INSTELLINGEN" ............................................................................................................................153
7.3.1 MENU "WELDING" - "LASSEN" ...............................................................................................................................153
7.3.2 MENU "MACHINE" - INSTELLINGEN MACHINE". ..............................................................................................154
7.3.3 MENU "FACTORY SETUP" - "HERSTEL FABRIEKSINSTELLINGEN ................................................................154
7.3.4 MENU "LANGUAGES" - "TAALINSTELLINGEN" .................................................................................................154
7.4 MENU INFORMATIE .............................................................................................................................................................154
8 SNELKEUZEMENU. ........................................................................................................................................................................154
8.1 "MEM" - "OPSLAAN" .............................................................................................................................................................154
8.2 "PAR" - "PROCESPARAMETERS" ........................................................................................................................................154
8.3 "2T/4T" - "TWEETRAPS / VIERTRAPS" ..............................................................................................................................154
8.4 "JOB" - "BEWERKINGSPROGRAMMA'S" ..........................................................................................................................154
8.5 "H2O"
8.6 "WIZ" WIZARD .......................................................................................................................................................................154
9. LASSEN
9.1 MIG/MAG LASSEN .................................................................................................................................................................154
9.1.1 MIG ---- SYNERGETISCH MIG/MAG LASSEN ......................................................................................................154
9.1.2 MIG MAN. NORMAAL MIG/MAG LASSEN ............................................................................................................154
9.1.3 MIG HD. SYNERGETISCH MIG/MAG LASSEN MET GROTE AFZETTING .......................................................155
9.1.4 MIG ROOT SYNERGETISCH MIG/MAG LASSEN .................................................................................................155
9.1.5 MIG
9.2 MMA LASSEN .........................................................................................................................................................................155
9.3 TIG LASSEN .............................................................................................................................................................................156
9.3.1 MACHINES MET APARTE DRAADSLEPER. ..........................................................................................................156
9.3.2 COMPACTE MACHINES .............................................................................................................................................156
10 STORINGSCODES ...........................................................................................................................................................................156
11 ONDERHOUD
11.1 ONDERHOUD GENERATOR .................................................................................................................................................157
11.2 HANDELINGEN NA EEN REPARATIE ...............................................................................................................................157
140
................................................................................................................................................................................154
................................................................................................................................................................................154
PULSEREND SYNERGETISCH MIG/MAG-LASSEN ..........................................................................155
................................................................................................................................................................................157
INDEXEREN