Use; Starting When The Engine Is Cold; Starting When The Engine Is Hot; Turning The Engine Off - FLORABEST FBKS 52 A1 Originalbetriebsanleitung

Use

CAUTION!
► Please pay attention to the statutory provisions in the relevant noise
protection regulations.
Before starting the appliance, always check that:
■ The fuel system is not leaking.
■ The protective equipment and cutting equipment is complete and in
perfect working order.
■ All screw connections are firmly tightened.
■ All moving parts can move smoothly and freely.

Starting when the engine is cold

WARNING!
► Engage the chain brake before every use (push hand guard
forwards).
CAUTION!
► Never allow the starter pull cord
damage.
♦ Remove the cover from the guide rail
♦ Place the chainsaw on a firm, level surface. The saw chain
touch the ground.
♦ Push the front hand guard
The saw chain will be locked by the chain brake.
♦ Press the fuel pump "Primer"
♦ Switch the On/Off switch
♦ Pull the choke out.
♦ Place the tip of your shoe into the rear hand guard
page fig. B).
♦ Hold the chainsaw firmly by the front handle
pull cord slowly until you feel resistance.
♦ Now pull the starter pull cord
If the engine does not start, repeat the process.
As long as the choke is out, the engine will only run for a short time
and then switch off.
♦ Push the choke back in as soon as the engine has switched off.
♦ Now pull the starter pull cord
starts. The engine now idles
If the engine does not start after several attempts, read the "Troubleshooting
guide".
CAUTION!
► Always pull the starter pull cord
the starter pull cord firmly when the starter pull cord
Do not allow the starter pull cord
NOTE
► At very high outdoor temperatures it is possible that even a cold
engine has to be started without using the choke!
FBKS 52 A1
to whip back. This could cause
.
forwards until it clicks into place.
6 times.
to "I".
(see fold-out
and pull the starter
quickly so that the engine starts.
quickly again so that the engine
straight out. Hold the handle of
retracts.
to whip back.
♦ Release the chain brake by pulling the front hand guard
(see fold-out page fig. C).
CAUTION! The chain brake is now released and the saw chain
now runs freely.
NOTE
► If the saw chain
when you release the throttle, you need to adjust the carburettor
(see section "Maintaining the carburettor settings").
♦ Lift the chainsaw.
♦ Hold the front handle
♦ Hold the rear handle
hand now lies on the throttle control lock
operates the throttle control
♦ After pulling the throttle
♦ Run the engine to warm it up.

Starting when the engine is hot

(The appliance has been turned off for less than 15–20 minutes)
♦ Push the front hand guard
The saw chain
must not
♦ Switch the On/Off switch
♦ The choke lever
motor.
♦ Place the tip of your shoe into the rear hand guard
page fig. B).
♦ Hold the chainsaw firmly by the front handle
pull cord slowly until you feel resistance.
♦ Now pull the starter pull cord
after 1–2 pulls. If the appliance still hasn't started after 6 pulls, repeat
the process as described in "Starting when the engine is cold".
Turning the engine off
Emergency stop sequence
If you need to stop the appliance immediately, switch the On/Off switch
to "0".
Normal sequence
♦ Release the throttle control
Off switch to "0".
CAUTION!
► When idling, the saw chain
If the saw chain
Working procedures
Get to know the chainsaw before you start to use it.
moves when it is idling or the engine goes out
firmly in your left hand.
firmly in your right hand. The ball of your
and your index finger
(see fold-out page fig. D).
once, the engine should idle.
forwards until it clicks into place.
will be locked by the chain brake.
to "I".
does not need to be pulled out to start a warm
and pull the starter
quickly. The appliance should start
. The engine idles. Then switch the On/
should not move.
moves, you need to adjust the idling speed!
GB │ IE │ NI
backwards
(see fold-out
│
9 ■