hilscher DTM Bedienungsanleitung Seite 145

Fehlercodes
ODM-Fehlercodes DBM V4
Fehlercode (Definition)
CDBM_E_ADR_STRING_ERROR
CDBM_ERROR_FROM_VAR_ CHANGE_TYPE
CDBM_E_MINERROR
CDBM_E_MAXERROR
CDBM_E_RANGE_ERROR
CDBM_E_TABLE_TYPE1
CDBM_E_TABLE_TYPE3_ ADDREC
CDBM_E_TABTYPE1
CDBM_E_TOGGLE_NOT_FOUND
CDBM_E_TOGGLE_VALUE_IS_ EMPTY_STRING
CDBM_VARIANT2BYTEARRAY_ ERROR
CDBM_E_SET_ELEM_PROP_ DEPENDENCY
CDBM_E_TABTYPE1_REC_
DOESNT_CORRESPOND_ WITH_ELEMENT
CDBM_TABTYPE1_NO_DATA_
FOUND_FOR_RECORD
CDBM_E_TABTYPE1_WRITE_
ELEMENT_NE_RECORD
CDBM_E_TABTYPE1_WRITE_
ELEMENT_NOT_FOUND
CDBM_I_TABLE_NAME_EXCEEDS_
RCS_RANGE
CDBM_W_CUT_STRING
CDBM_I_STRING_TOO_SHORT
CDBM_I_STRING_TOO_LONG
CDBM_E_STRING_TOO_SHORT
CDBM_E_STRING_TOO_LONG
DTM für EtherNet/IP-Scanner-Geräte | Konfiguration von EtherNet/IP-Scanner-Geräten
DOC061201OI07DE | Revision 7 | Deutsch | 2013-09 | Freigegeben | Öffentlich
Wert Beschreibung
0XC004C847 The given Address string doesn't fit the
required format of this type where all
address bytes must be in the range
between 0 and FF
0XC004C848 Function VariantChangeType return an
error when trying to convert the Parameter
0XC004C849 Error while comparing the Value with the
lower range
0XC004C84A Error while comparing the Value with the
upper range
0XC004C84B Value out of Range
0XC004C84C Table type 1 doesn't have a unique record
length over all records
0XC004C84D Table type 3 doesn't allow to insert more
than one Record
It's not allowed to insert more Records
0XC004C84E
than structure definitions in Table Type 1
0XC004C84F Could not find the string for this value in
the list of valid toggle strings
0XC004C850 The toggle string for this value is empty.
0XC004C851 Error during conversion of Variant to byte
array
0XC004C852 The Toggle Type needs also the additional
string and the additional number entries in
the Method
0XC004C853 When reading the records of Table type 1
elementwise the record number must
correspond with the element number
0XC004C854 When reading the records of Table type 1
and structure definitions are present it's
assumed that for each structure element a
corresponding record must exist
0XC004C855 When writing the records of Table type 1
elementwise and structure definitions are
present it's only allowed to write the
corresponding element number in each
record
0XC004C856 When writing the records of Table type 1
with an array and structure definitions are
present it's assumed that a corresponding
element number of this record exist
0X4004C857 The Table name exceeds the maximum
length of RCS compatible Table names
(Informational)
0X8004C858 The string exceeds the maximum length
and will be limited to the maximum length
(Warning)
0X4004C859 The string is below the minimum length.
The minimum length will be reduced.
(Informational)
0X4004C85A The string is exceeding the maximum. The
maximum length will be extended.
(Informational)
0XC004C85B The string is below the minimum length.
(Error)
0XC004C85C The string is exceeding the maximum
length
(Error)
145/154
© Hilscher, 2006-2013