Connecting A Vcr; Using The Scart Output Function; Vcr Playback - Pioneer KRP-600A Bedienungsanleitung

12 Using with other equipment

Connecting a VCR

Use the INPUT 2 terminals when connecting a VCR and other
audiovisual equipment.
If your VCR supports TV-VCR advanced "AV link" systems, you can
connect the VCR to the INPUT 2 or INPUT 3 terminal on the flat
screen TV using the fully-wired 21-pin SCART cable.
AV link advanced system
• Download tuning information directly from TV to VCR (Preset
download).
• While watching TV, you can record a programme with a one-
touch press of the VCR recording button. (WYSIWYR*)
* Refer to your VCR operation manual as some VCRs have an
exclusive key for WYSIWYR.
• When you press the play button on the VCR, the system
automatically turns on from standby and displays a VCR image.
Note
• TV-VCR advanced "AV link" systems may not be compatible with
some external sources.
ANT
Media Receiver (rear)
Caution
• If you connect a device such as a VCR between the aerial and
Media Receiver, signal reception quality may deteriorate. In this
case, we recommend using a distributor and making sure to
switch the "Aerial Power" setting off in order to prevent the
device from being damaged.

VCR playback

To watch a VCR image, press INPUT 2 on the remote control unit or
press INPUT on the Media Receiver to select "INPUT 2".
Note
• If VCR images do not come in clearly, you may need to change
the input signal type setting using the menu. See page 59.
66
En
INPUT 1 INPUT 2 AUDIO
INPUT 2
LAN (10 / 100) DIGITAL OUT
SAT
INPUT 3
HDMI HDMI
OPTICAL INPUT 1 INPUT 3
SCART cable
VCR
• Connect external equipment to only terminals that are to be
actually used.
• Refer to your VCR operation manual for the signal type.

Using the SCART output function

This function allows you to record DTV programmes with a
connected VCR or other recording equipment while enjoying
watching the flat screen TV as usual. With this function, you can
also easily enjoy timeshift playback when a DVD/HDD recorder
(DVR) is connected.
The following diagram assumes that you connect a Pioneer DVR-
940HX-S to the Media Receiver so that you can enjoy timeshift
playback with the recorder.
ANT
Media Receiver (rear)
Y P B P R
COMPONENT VIDE
R L
SUB WOOFER O
C
OU
HDMI
INPUT 4
In addition to the above connections, you need to perform the
following:
• See Switching the SCART output (page 67) and select "Fixed on
DTV/SAT" for "SCART Output" in the Setup menu.
• On the DVD/HDD recorder (DVR), select the video/audio input
source matching the external input terminal to which the Media
Receiver has been connected. For this method, see the
operation manual that came with the recorder.
• Select the input source on the Media Receiver depending on the
terminal to which the output of the DVD/HDD recorder (DVR)
has been connected; for the above connection example, select
"INPUT 2".
• When you complete the connections and setups, you can then
enjoy timeshift playback with the DVD/HDD recorder (DVR). You
can also select the 2-screen or picture-in-picture mode to watch
images coming from the DTV input source and an external input
source ("INPUT 2" for the above connection example) to which
the output of the recorder has been connected.
INPUT 1 INPUT 2
LAN (10 / 100) DIGITAL OUT
SAT
INPUT 3
OPTICAL
SCART cable
SCART cable
Y P P
B R
COMPONENT VIDE
AUDIO R L
INPUT 2 SUB WOOFER O
C
OU
HDMI HDMI HDMI
INPUT 1 INPUT 3 INPUT 4
DVR-940HX-S