Operation; All Models; Maintenance; General - Hatco Toast King Installations- Und Bedienungsanleitungen

OPERATION

ALL MODELS

1. Plug cabinet into an electrical outlet of the correct voltage, size
and plug configuration. See Specifications for details.
2. Turn the Selector Switch, located on the front panel, to "Toast"
or "Buns". See 7 .
NOTE: When toasting buns, place cut side down and set Selector
Switch to the "Buns" position. When toasting bagels, place cut side
up and set Selector Switch to the "Toast" position.
3. Turn the Speed Control to the lightest/fastest position while
the unit heats up.
NOTE: Allow approximately 15 minutes for a warm-up period.
4. After warm-up period, set the Speed Control to medium
position and toast two slices of bread product. Adjust the Speed
Control to the desired amount of browning.
NOTE: To toast moist products such as English muffins, rye bread
or whole wheat, slow the conveyor by turning the Speed Control
knob to a slower/darker setting (clockwise).
!
CAUTION
The toasting of coated products such as garlic bread, cheese
sandwiches and sweet rolls is NOT recommended. Residue will
reduce toaster performance and could possibly ignite inside
the toaster.

MAINTENANCE

GENERAL

Hatco Electric Conveyor Toasters are designed for maximum
durability and performance, with minimum maintenance.
!
WARNING
To avoid any injury, turn the power switch off, unplug the unit
from the power source and allow to cool before performing
any maintenance.

CLEANING

!
WARNING
This appliance is not of jet-proof construction. Do not use
jet-clean-spray to clean this appliance.
Exterior
To preserve the bright finish of the unit, it is recommended that
the exterior surfaces be wiped daily with a damp cloth. Stubborn
stains may be removed with a good stainless steel cleaner
or a non-abrasive cleaner. Hard to reach areas should be cleaned
with a small brush and mild soap.
CAUTION
Abrasive cleaners could scratch the finish of your toaster.
Toast Collector Pan
Remove from unit and wash with soap and water, then rinse.
Baskets
1. Use the manual advance knob on the right side of the unit
to advance the baskets without energizing the unit.
Form No. TR/TKCEM-0902
CAUTION
Maximum Product Thickness: 3 cm (1-1/4"). Toasting of thicker
products is NOT recommended. Products thicker than
3 cm (1-1/4") will cause the conveyor system to jam which could
possibly ignite product inside the toaster.
Manual Advance
The manual advance knob is located on the right side panel
of the toaster. This knob permits manual rotation of the baskets
and allows rapid discharge of toast. During the cleaning operation,
the manual advance knob permits rotation of the baskets
for removal without energizing the toaster.
Thermostat Adjustment
The thermostat adjustment screw is located on the control panel.
This thermostat controls the toasting chamber temperature.
The thermostat is preset at the factory, but may be adjusted
as follows:
Using a small screwdriver, turn the adjustment screw. See 7 .
clockwise to increase temperature or counterclockwise to decrease
the temperature.
NOTE: Do not turn screw more than 1/8 turn at a time. Allow
at least 5 minutes for temperature to stabilize.
!
CAUTION
Be sure baskets are cool before removal. if not cool, baskets
could cause burns.
2. Remove the baskets by pushing the spring-loaded chain away
from the basket while pulling the basket to the left and out.
See 8 .
NOTE: Do not detach hold down bars when cleaning baskets.
3. Wipe clean with a soft, damp cloth or soak the baskets
in a mild solution of soap and water.
4. Re-install baskets by aligning pin on chain with holes in toaster
basket. Right side pin must be exactly opposite the pin
on the left-hand chain.
5. To attach balance of baskets, advance the conveyor and repeat
procedure. Each basket is hung immediately below the
preceding basket, otherwise, all baskets cannot be installed.
CAUTION
Misalignment of the baskets will cause the conveyor to jam.
If hold down bars are separated from the baskets, be sure
the bars are not reversed when re-installed. Hold down bar
stops should be at the left with bar flat on basket. Incorrectly
positioned bars will cause the conveyor to stop.
9