Gwarancja I Serwis - VERTO 51G427 Betriebsanleitung

GWARANCJA I SERWIS

Warunki gwarancji oraz opis postepowania w przypadku reklamacji
zawarte są w załączonej Karcie Gwarancyjnej.
Serwis Centralny
GTX Service
Ul. Pograniczna 2/4
02-285 Warszawa
Sieć Punktów Serwisowych
i pogwarancyjnych dostępna na platformie internetowej gtxservice.pl
Grupa Topex zapewnia dostępność części zamiennych oraz
materiałów eksploatacyjnych dla urządzeń i elektronarzędzi.
Pełna oferta części i usług na gtxservice.pl. Zeskanuj kod QR i wejdź:
tel. +48 22 573 03 85
fax. +48 22 573 03 83
e-mail service@gtxservice.pl
do napraw gwarancyjnych
GB
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
BENCH GRINDER
CAUTION: BEFORE USING THE POWER TOOL READ THIS MANUAL
CAREFULLY AND KEEP IT FOR FUTURE REFERENCE.
DETAILED SAFETY REGULATIONS
SPECIAL CONDITIONS REGARDING SAFETY OF BENCH GRINDER
OPERATION
• Closely follow the instructions from bench grinder manual;
• Do not use damaged grinding wheels;
• Use grinding wheels recommended by the manufacturer only,
which are labelled to work with the speed specified on the grinder
rating plate or higher;
• Adjust spark shields often enough to compensate wear of wheel, to
the smallest possible distance between the wheel and the shield,
not greater than 2 mm;
• Firmly fix to the bench grinder all elements, which ensure safety;
• Do not start grinding when elements for safe operation are not
installed (use shield when grinding);
• During operation use personal protection measures appropriate for
used machine (glasses or anti-splinter goggles, face shield, earmuff
protectors, protection half-mask, safety shoes, protective gloves
and other pieces of protective measures);
• You can proceed only with such type of grinding that the grinding
wheel is designed for (consider limitations of application, safety
regulations and other information);
• Always unplug the power cord from the mains socket before
commencing any activities related to adjustment, maintenance, or
grinding wheel replacement;
• Always ensure that eye shields attached to bench grinder are
correctly positioned;
• When the grinder is not being used, it should be switched off.
Never leave the grinder unattended if it is not switched off and the
plug is not removed from mains socket. Never leave the grinder
unattended before complete stop of grinding wheels;
• Do not use grinding wheels with maximum rotational speed below
2950 rpm;
• Persons below 18 years old cannot use the bench grinder;
• Do not leave cloths, pieces of garment, ropes, cords and other
similar objects in proximity of the bench grinder;
• Whenever operator is being addressed to, prior to leaving the tool
the current operation must be finished and then the tool must be
switched off;
• From time to time ensure that all nuts, bolts and other fixing
elements are properly fastened and secured;
• Do not over-tighten nuts that fix grinding wheels;
• Do not use grinding wheel that was hit, especially side surface;
• Replace wheel that is cracked or is suspected to be damaged;
• After installation of new grinding wheel always allow it to rotate for
few minutes at full rotational speed prior to operation. Whenever
the grinder is switched on, its operator should stand at side of it;
• Prior to every start up of the grinder ensure the grinding wheels
can rotate freely;
• Do not use the grinder until all shields are fixed and secured in
appropriate way;
• Prior to starting operation ensure that tool supports are
appropriately set;
• Do not overload the bench grinder. Allow the bench grinder to work
at full rotational speed or at speed close to maximum;
• Never apply excessive pressure on grinding wheel. It may crack, that
may injure the operator;
• Do not use the bench grinder for cutting;
• Prior to starting the grinder ensure the grinding wheel has no
contact with processed material;
8
51G427