Additional Safety Rules - Makita 6826 Betriebsanleitung

18. Disconnect the plug from the power source and/
or the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
19. Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
20. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
21. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
22. Use the power tool, accessories and tool bits
etc. in accordance with these instructions and in
the manner intended for the particular type of
power tool, taking into account the working con-
ditions and the work to be performed. Use of the
power tool for operations different from those
intended could result in a hazardous situation.
Service
23. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
24. Follow instruction for lubricating and changing
accessories.
25. Keep handles dry, clean and free from oil and
grease.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces
when performing an operation where the cut-
ting tools may contact hidden wiring or its
own cord. Contact with a "live" wire will make
exposed metal parts of the tool "live" and
shock the operator.
2. Always be sure you have a firm footing. Be
sure no one is below when using the tool in
high locations.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely
hot and could burn your skin.
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Depth adjustment
The depth can be adjusted by turning the locking
sleeve. Turn it in "A" direction for less depth and in "B"
direction for more depth. One full turn of the locking
sleeve equals 1.5 mm change in depth. (Fig. 1)
Adjust the locking sleeve so that the distance
between the tip of the locator and the screw head is
approximately 1 mm as shown in Fig. 2. Drive a trial
screw into your material or a piece of duplicate mate-
rial. If the depth is still not suitable for the screw, con-
tinue adjusting until you obtain the proper depth
setting. (Fig. 2)
Removing or installing bit (Fig. 3 & 4)
Important:
Always be sure that the tool is switched off and
unplugged before removing or installing the bit.
To remove the magnetic socket bit, first pull the loca-
tor out of the locking sleeve. Then pull the magnetic
socket bit. To install the magnetic socket bit, insert it
into the tool as far as it will go. Then install the locator
by pushing it firmly back onto the locking sleeve.
Switch action (Fig. 5)
CAUTION:
Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
"OFF" position when released.
To start the tool, simply pull the trigger. Tool speed is
increased by increasing pressure on the trigger.
Release the trigger to stop. For continuous operation,
pull the trigger and then push in the lock button. To
stop the tool from the locked position, pull the trigger
fully, then release it.
NOTE:
ENB004-1
Even with the switch on and motor running, the bit
will not rotate until you fit the point of the bit in the
screw head and apply forward pressure to engage
the clutch.
Reversing switch action (Fig. 6)
CAUTION:
• Always check the direction of rotation before opra-
tion.
• Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of rota-
tion before the tool stops may damage the tool.
This tool has a reversing switch to change the direc-
tion of rotation. Move the reversing switch lever to the
"A" side for clockwise rotation or the "B" side for
counterclockwise rotation.
5