Specifications; Additional Safety Rules For Tool - Makita BTD040 Betriebsanleitung

ENGLISH
1 Battery cartridge
2 Button
3 Indicator lamp
4 Capacity
5 Bit
6 Sleeve
7 Switch trigger

SPECIFICATIONS

Model
Capacities
Machine screw .......................................................................... M4 – M8
Standard bolt .............................................................................M5 – M10
High tensile bolt......................................................................... M5 – M8
–1
No load speed (min ).................................................................. 0 – 2,500
Impacts per minute....................................................................... 0 – 3,500
Overall length ............................................................................... 164 mm
Net weight .................................................................................... 1.0 kg
Rated voltage ............................................................................... D.C. 9.6 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may result
in a risk of overheating, possible burns and even
an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
4
Explanation of general view
8 Reversing switch lever
9 A side
10 B side
11 Clockwise
12 Counterclockwise
13 N•m (kgf•cm)
14 Fastening torque
7.
8.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
ENC005-1
2.
3.
4.

ADDITIONAL SAFETY RULES FOR TOOL

1.
2.
3.
4.
5.
SAVE THESE INSTRUCTIONS.
15 Proper fastening torque for
16 Seconds
17 Fastening time
18 Limit mark
19 Brush holder cap
20 Screwdriver
BTD040
Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
Be careful not to drop or strike battery.
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
Be aware that this tool is always in an operating
condition, because it does not have to be
plugged into an electrical outlet.
Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring. Contact with a "live"
wire will make exposed metal parts of the tool
"live" and shock the operator.
Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
Hold the tool firmly.
Wear ear protectors.
BTD060
M4 – M8
M5 – M12
M5 – M10
0 – 2,500
0 – 3,000
164 mm
1.0 kg
D.C. 9.6 V
ENB024-1