Specifications; Additional Safety Rules - Makita 6823N Betriebsanleitung

ENGLISH
1 Locking sleeve
2 Approximately 1 mm
3 Locator

SPECIFICATIONS

Model
Capacities
Self drilling screw ................................................................................... 6 mm
Drywall screw ......................................................................................... 6 mm
–1
No load speed (min ) ............................................................................... 0 – 2,500
Overall length ............................................................................................ 301 mm
Net weight ................................................................................................. 1.5 kg
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Note: Specifications may differ from country to country.
Intended use
The tool is intended for screw driving in wood, metal and
plastic.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to the enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tools
may contact hidden wiring or its own cord. Con-
tact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
4
Explanation of general view
4 Bit
5 Magnetic bit holder
6 Switch trigger
OPERATING INSTRUCTIONS
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
tool.
Depth adjustment
The depth can be adjusted by turning the locking sleeve.
Turn it in "A" direction for less depth and in "B" direction
for more depth. One full turn of the locking sleeve equals
1.5 mm change in depth. (Fig. 1) Adjust the locking
sleeve so that the distance between the tip of the locator
and the screw head is approximately 1 mm as shown in
Fig. 2 or 3. Drive a trial screw into your material or a
piece of duplicate material. If the depth is still not suitable
for the screw, continue adjusting until you obtain the
proper depth setting. (Fig. 2 & 3)
Installing or removing bit (Fig. 4 & 5)
Important:
Always be sure that the tool is switched off and
ENB004-1
unplugged before removing or installing the bit.
To remove the bit, first pull the locator out of the locking
sleeve. Then grasp the bit with a pair of pliers and pull the
bit out of the magnetic bit holder. Sometimes, it helps to
wiggle the bit with the pliers as you pull.
To install the bit, push it firmly into the magnetic bit
holder. Then install the locator by pushing it firmly back
onto the locking sleeve.
Switch action (Fig. 6)
CAUTION:
Before plugging in the tool, always check to see that the
switch trigger actuates properly and returns to the "OFF"
position when released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop. For continuous opera-
tion, pull the switch trigger and then push in the lock but-
ton. To stop the tool from the locked position, pull the
switch trigger fully, then release it.
NOTE:
Even with the switch on and motor running, the bit will not
rotate until you fit the point of the bit in the screw head
and apply forward pressure to engage the clutch.
7 Lock button
8 Reversing switch lever
9 Hook
6823N 6824N
6 mm
5 mm
0 – 4,500
290 mm
1.4 kg